Mitsuma
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/13/2025 in #fix-my-printer
Am I screwed?
there are/were heater core replacements but might as well buy a new Rapido Ace or so
5 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/13/2025 in #fix-my-printer
Am I screwed?
its a v1 Rapido
and yes you are basically screwed, not possible to reattach those
5 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
you just need to overwrite the dir pin direction in config
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
steppers/cables are not always 100% the same direction
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
yes technically you can also reverse the coils on the plug but a ! in the config is easier
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
you need to reverse one or both
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
the config
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
ideally you would loosen the belts now so it doesnt actually skip
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
its a bit tricky to find out which one.
you can tell it to move Y back and watch which of the Y Hybrid steppers is moving the wrong way and skipping
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
one or both
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
your hybrid steppers are wrong direction
18 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
contact RatRig for a replacement
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
beacon can be damaged when plugging in USB while power
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
make sure you dont plug in the beacon while powered, always power it off first
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
well if its fine now, reconfigure for beacon, plug in the beacon and see again
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
which reduces the issue to the beacon/beacon usb cable
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
well if everything is running fine now, you can exclude its anything current
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
its a pretty good USB hub tho, shouldn't have caused problems on there
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
its not that critical but common practice
131 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Error after some minutes idling.
so the Octopus and the two toolboards you probably want on that
131 replies