Bluegoose59
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/15/2023 in #ratos-support
EBB42 x endstop not functional
9 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/15/2023 in #ratos-support
EBB42 x endstop not functional
I had to modify the end stop to include a cap and pull up resistor that fixed the issue.
9 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
The syntax is for reference [tmc2209 extruder]
uart_pin: toolboard:e_uart_pin
run_current: 0.850
stealthchop_threshold: 0
interpolate: False
14 replies
RRCRat Rig Community [Unofficial]
•Created by sunny-green on 4/28/2023 in #fix-my-printer
EBB36 + Orbiter 2.0 - Buzzing - Not moving
I have a similar issue, how did you enter the current in to the printer.cfg as I can't work out the syntax
2 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/15/2023 in #ratos-support
EBB42 x endstop not functional
It works on the main board as it should. I will look at re-flashing the EBB
9 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/15/2023 in #ratos-support
EBB42 x endstop not functional
Yes , I've tried 2 and 3 way end stops both the same. PB6 goes high to low but no state change in kipper using QUERY_ENDSTOPS
9 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
I will give it a look in the morning, seems the macros file has been corrupted for whatever reason thanks for your help.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
[stepper_e]
run_current: toolboard: 0.850
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
I have the steps calibrated in user overrides , but current setting is eluding me for the EBB42. Using Kipper / EBB documentation the syntax is giving errors.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
Not knowing much about Kipper as I'm used to Duet RepRap so far most / all working apart from this. Thanks
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
The problem is the EBB42 is not referenced as far as I can see in Kipper. I will keep looking thanks.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
I've done the XYZ but get an error on E
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/12/2023 in #ratos-support
Tool board stepper motor setting
Do you happen to know the syntax?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Bluegoose59 on 9/11/2023 in #ratos-support
42BYGHW811 stepper motors
OK Thanks I will give that a go.
3 replies