Zimt Snad
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 11/24/2024 in #fix-my-resonance
Can't get second peaks to align
Should i actually omit the belt tension tuning and print so stuff and come to it after few hours of printing?
3 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
I guess am gonna close this post then
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
Like 2 meters above
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
I would say emf because in that previous room there was quite big antenna array not that far away
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
I just moved my printer to a diffrent room and it works fine now?
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
Might as well notify them
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
did that already just for sanity checking
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
I've added that tiny bit of missing solder but it didn't help the issue
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
or maybe not
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
i think i've found my issue
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
just when doing the beacon calibration
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
if i remember correctly my beacon is currently connected to usb 3
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
exaclty
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
it also does that just fine
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
55 replies
RRCRat Rig Community [Unofficial]
•Created by Zimt Snad on 10/20/2024 in #fix-my-printer
Beacon probe failing to pass BEACON_RATOS_CALIBRATE
my nozzle didn't touch the bed once
55 replies