SimonSolar2C
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 4/3/2025 in #ratos-support
extruder sensor transient zero problem
okay looks like sm ooth time in the extruder section may be causing the sutdown - so I took that out and got another sutdown when i closed the lid - very carefully measured at the plug - no voltage this time - time for rewiring back to the board. i wish these wires wouldnt break randomly - so hard to debug !
7 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 4/3/2025 in #ratos-support
extruder sensor transient zero problem
okay smooth_time 2.0 was causing that repeated shutdown. i'll try 0.1s
7 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 4/3/2025 in #ratos-support
extruder sensor transient zero problem
meaning i cant find a section temperature_sensor in printer.cfg
But further troubleshooting and printer keeps resetting as if there's a broken wire in the hotend sensor, and yet, it reads 3.3volts at the hotend plug, and sensor reads 110kohms when disconnected at that plug. making no sense to me!
7 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 4/3/2025 in #ratos-support
extruder sensor transient zero problem
and in anothjer discussion it was recommened to use [extruder]
smooth_time: 1.0
7 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 8/13/2024 in #ratos-support
Octopus firmware version mismatch
6 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 8/13/2024 in #ratos-support
Octopus firmware version mismatch
6 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 8/13/2024 in #ratos-support
Octopus firmware version mismatch
6 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 11/29/2023 in #ratos-support
mcu shutdown - lost communication
5 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 11/29/2023 in #ratos-support
mcu shutdown - lost communication
5 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 11/29/2023 in #ratos-support
mcu shutdown - lost communication
Further info to the above, I followed the install instructions here:
https://www.obico.io/blog/klipper-camera-mainsail/
5 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 10/15/2023 in #ratos-support
Webrtc camera stopped working
10 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 10/15/2023 in #ratos-support
Webrtc camera stopped working
10 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 9/17/2023 in #ratos-support
mcu shutdown Timer too close - Octopus, Pi4, Vcore3, 500
4 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 9/17/2023 in #ratos-support
mcu shutdown Timer too close - Octopus, Pi4, Vcore3, 500
Okay turns out I have a RasPi3B, which should still be suitable, but perhaps some tweaks are needed - can I run Obico and webcam service, for example?
4 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 9/17/2023 in #ratos-support
mcu shutdown Timer too close - Octopus, Pi4, Vcore3, 500
4 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 7/21/2023 in #ratos-support
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
10 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 7/21/2023 in #ratos-support
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
10 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 7/21/2023 in #ratos-support
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
10 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 7/21/2023 in #ratos-support
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
10 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 7/21/2023 in #ratos-support
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
Thanks - Ive had a read - but there are so many rabbit holes to go down with this 'Timer too close' how do you know its the SD card at fault - does the graph tell you that?
10 replies