Kevin Schwarz
RRCRat Rig Community [Unofficial]
•Created by armearme. on 2/10/2025 in #fix-my-printer
VC4 Hybrid pauses at random ocasions after Orbiter 2 Smart Sensor was installed.
Just leave everything connected as is and disable the filament tangle detection in your OrbiterSensor.cfg in the upper part of the vorresponding file, there should be a number of features that can be easily deactivated with the change from False to True.
25 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
On ratrig’s website there is a good overview in the documentation.
And if you only need a simple list, without explaination, check the dashboard macro area. There are sole icons in the top bar of the section. One of them shows a list of all commands.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
If you use shaper_calibrate, i belive it will add the input shaper values further down in the „autogenerated“ section of the file.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
Don‘t worry 🤣
19 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
@Hesus
or just use the macro SHAPER_CALIBRATE Then after finishing, SAVE_CONFIG
or just use the macro SHAPER_CALIBRATE Then after finishing, SAVE_CONFIG
19 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
Can you show me a screenshot?
You need to add this section, including the first line with the input shaper keyword:
[input shaper]
shaper_freq_x: xx.x
shaper_type_x: mzv
19 replies
RRCRat Rig Community [Unofficial]
•Created by Hesus on 2/26/2025 in #fix-my-printer
Input shaper error
Without the Hashtags.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
No this isn‘t what i‘m suggesting, but traditionally i found it easier to troubleshoot problems with a simple filament like PLA and then later move on to more finnicky filament.
Also this makes it easy to rule out the slicer filament settings as PLa will genereally print quite fine, even if the numbers are a bit off.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Do you have the same artifacting with other filament like pla? You could try that with a generic profile for pla.
18 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/25/2024 in #fix-my-print
Weird Artifacts
Im not really sure, but what I saw was heavy „ringing“ like a pattern on Y and slight layershifts on X.
13 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/25/2024 in #fix-my-print
Weird Artifacts
The pattern can also be caused by an unaligned X gantry. You can easily check that if you move the x gantry to the front of the printer and check if the left and right xy-joiners have the same distance to the frame. If not, a normal y move causes the gantry to lock and cause this kind of pattern on the print.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
How tight is the screw on your orbiter tension lever? I had a similar print result with a screw that was much too tight. That led to filament getting grinded slightly. Especially when doing small, fast moves.
The right tension for me is actually quite low, just maybe two full turns after the screw grabs onto the orbiter.
18 replies