Erik_
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
I dont know. It feels like it should be able to print at a decent speed.
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
I use 90% speed
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
My best guess is that the motor is malfunctioning.
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
I have loosened up the belts. Sound less ratling but the offset i still there
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Okay, so pretty loose then but not as loose as they would fall off the pulley. I can try to loosen them up i suppose
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
How much should the belt be tensioned?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
So the motor is bad perhaps?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Its so wierd. It creates the first layer perfectly but not the following layers.
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Ok. I am just guessing. There must be some system that reads its position i assume.
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
So the probe sensor should be fine it can read x axis correct i suppose?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
So, that's a clue atleast.
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
What i can tell is that is only offsetting in Y axis
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Not sure what to do mate
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
It is not suppose to sound like that?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Or is the sensor reading wrong cordinates so that the system thinks it is at the right place but it is not?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
It must be a firmware / soft issue?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
Still problem with offset..
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
63 replies
RRCRat Rig Community [Unofficial]
•Created by Erik_ on 12/2/2024 in #fix-my-print
x & y offset in middle of print?
:). Yea i deleted all the previouse configs and ran a new setup. Now Z-TILT is working again.
63 replies