soap
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
10 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/18/2025 in #fix-my-mesh
Bed mesh on vcore 3.1 500 how to fix beacon
I had a similar problem and was able to find a solution eventually. I detaield some steps in my forum post that might be able to help you https://discord.com/channels/582187371529764864/1335447142348623954
2 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
10 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
10 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
I added the following lines to printer.cfg and it seemed to fix the z-tilt probing the wrong areas. However, now I'm getting an error when doing a bed mesh "move out of range"
10 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
I think I found the problem but I don't know how to fix it yet. At z1 the beacon misses the PEI plate and registers off the build plate instead. I need to change the Z-tilt measuring locations somehow
10 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 2/2/2025 in #fix-my-mesh
Vcore 3.1 400 after beacon configuration
10 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
It's fascinating, I'll have to pick one up and try it out for myself.
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
I was definitely ambitious with the 20 haha
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
Well, I'm definitely seeing improvements. Tested at 200C and 215C and saw a 1.75mm3/s improvement but more importantly, dialed the max down to 14.5 mm3/s from 20. Reprinting the part from the photos with a fresh roll of filament now.
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
I strictly use PLA+ but I do plan to switch rolls as one of my next steps.
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
The strange part is that I haven't had any problems up until a couple of weeks ago. Idk what changed
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
Thank you for the suggestions!
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
I'll report back after the flow rate test. Printing it now
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
205c for first layer, 200c for the others. I can bump it up to 215 or 220 without affecting quality
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
Ah I see it. I'll give it a shot
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
I'm wondering if maybe the orbiter is wearing out and not able to grip at those faster extruder speeds?
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
Their site says 35mm3/s is the max. I ran the orca calibration test and my current flow rate was the best looking of the bunch.
29 replies
RRCRat Rig Community [Unofficial]
•Created by soap on 9/16/2024 in #fix-my-print
Flow Issues?
29 replies