Spinal-Tap
RRCRat Rig Community [Unofficial]
•Created by Spinal-Tap on 8/20/2024 in #fix-my-print
how to fix over extrusion.
yes Included the orbiter2 cfg and commented out the orbite 1.5 cfg
13 replies
RRCRat Rig Community [Unofficial]
•Created by Spinal-Tap on 8/20/2024 in #fix-my-print
how to fix over extrusion.
no. orbiter 1.5
13 replies
RRCRat Rig Community [Unofficial]
•Created by Spinal-Tap on 8/20/2024 in #fix-my-print
how to fix over extrusion.
the extruder is an Oribter 2 . what is a CHT? reducing the flow rate in the slicer has helped a lot and I think with continued testing and tuning in the slice I will get a good print quality.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Spinal-Tap on 8/20/2024 in #fix-my-print
how to fix over extrusion.
v-Core3 500, RatOS 2.0
13 replies
RRCRat Rig Community [Unofficial]
•Created by Spinal-Tap on 8/20/2024 in #fix-my-print
how to fix over extrusion.
"Extrusion: ~ 96 mm @ 24.1 mm³/s - 0.4 mm" does not change when change my rotational distance. I am testing changing the flow rate in my slicer now
13 replies
RRCRat Rig Community [Unofficial]
•Created by 🅰4⃣🍩 on 6/23/2024 in #fix-my-mesh
adding beacon mesh points?
I had to change the mesh_min values because the y_offset was causing move out of range errors
32 replies
RRCRat Rig Community [Unofficial]
•Created by 🅰4⃣🍩 on 6/23/2024 in #fix-my-mesh
adding beacon mesh points?
turns out I put my setting in the [bed_mesh] block in the printer config section after the [stepper_z2] section.
32 replies
RRCRat Rig Community [Unofficial]
•Created by 🅰4⃣🍩 on 6/23/2024 in #fix-my-mesh
adding beacon mesh points?
did you put it in user overrides?
32 replies
RRCRat Rig Community [Unofficial]
•Created by 🅰4⃣🍩 on 6/23/2024 in #fix-my-mesh
adding beacon mesh points?
give it a shot
32 replies
RRCRat Rig Community [Unofficial]
•Created by 🅰4⃣🍩 on 6/23/2024 in #fix-my-mesh
adding beacon mesh points?
add a block to you printer.cfg like this. Use values appropriate for you printer this blis from my 500.
zero_reference_position = the center of your bed probe_count is the value you asked about mesh, min and max will be extreeme poins of the scan and should be smalled than t your bed [bed_mesh] speed: 250 zero_reference_position: 250, 250 horizontal_move_z: 5 probe_count: 25,25 fade_start: 1.0 fade_end: 10.0 mesh_pps: 2,2 algorithm: bicubic bicubic_tension: .2 mesh_min: 20,30 mesh_max: 480,460
zero_reference_position = the center of your bed probe_count is the value you asked about mesh, min and max will be extreeme poins of the scan and should be smalled than t your bed [bed_mesh] speed: 250 zero_reference_position: 250, 250 horizontal_move_z: 5 probe_count: 25,25 fade_start: 1.0 fade_end: 10.0 mesh_pps: 2,2 algorithm: bicubic bicubic_tension: .2 mesh_min: 20,30 mesh_max: 480,460
32 replies