avery7250
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 8/28/2024 in #fix-my-printer
Z wobble? Wave
Thank you yea that was definitely something indidnt think to check the one had loosened off and started walking down so definitely a good thing to catch! Appreciate the help
6 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 8/28/2024 in #fix-my-printer
Z wobble? Wave
So far have not been able to find anything loose anywhere belts z axis bed not really sure where else I should be looking
6 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
after messing around with ellis print guide and abit of trial and error on the right settings and playing with orca abit more ive got on the right track of the settings to slowly fine tune. turning the nozzle hotter definitely helped alot, and figured out the fan settings a little bit how to work with layer time and %, ho still wish there was a way to overide it in ratos but maybe more playing will show. still not perfect prints but definitely useable now lowered my accel to decel and figured out how to get orca to run the right accels and speeds of things. all .3 layer height but running 150 start speed at 245 the jumping to 200mm/s with 255/260 ish nozzle temp to print properly. only battle now is the abs warping with what % to run the fan at, so far 35/40% with 4 seconds and 85 % on 1 second starting the fan 4 give or take layers up. came out with a 12 and 13 minute benchy, not following the rules but using for quality easy small print 3 walls .3 layer .6 nozzle 15% infil 18700 accel so i think thats running pretty good ill attach some pics later
16 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
going to 255c got the top surface looking awesome, little over extrusion on the short distances in the start and stop corner of the middle face. but there's still that line on the sides where that middle layer is so ill give the extrusion multiplier again and see how that does.
16 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
I believe the banging is the nozzle hitting lines previously printed on the same layer. And base layer is 150 rest is 200mm/s and a .3 inital and rest layer height so definitely not pushing max flow rate. And walls and small surface on top was good so i don’t believe it would be a clog. Clarifying 200 for everything else in the print. And the top layer is coming up not dropping down must be the pic angle. So ill try higher temp. I have no basis for the temp vs speed increases. 🙂 i had three top layers but also think you’re right about the fan cooling as well, would you have an idea what layer # ish to start on to prevent warping and what % ranges because ik 100% os way too much for abs lol
16 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
16 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
Yup that makes sense, thank you and ill give that a look over and try, i had done a bunch of the calibration in orca to get my initial values but it would make sense if im compensating the z first layer as to why the rest isnt right… getting the first layer right is only important if its correct not just looks right lol. Ill try those out tonight and post how i get along.
16 replies
RRCRat Rig Community [Unofficial]
•Created by avery7250 on 3/13/2024 in #fix-my-print
Flow? Temp? Speed?
Just measured the first layer on the last pic and youre right it measures .4 not the .3 it’s supposed to be in the slicer. In that case i would need to drop the flow rate so its not pushing as much through the nozzle?
16 replies