DOAmatrix
RRCRat Rig Community [Unofficial]
•Created by rival-black on 12/16/2024 in #german-support
4028 Lüfter
hast du beide lüfter aud den gleichen Pin ? wie sieht das aus was du in der config geschrieben hast ?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Kälte Kiste on 10/16/2024 in #german-support
Temperatur Problem nach Update 2.1 an Z2 Motor / Treiber
Hast du performance Mode ausgewählt ?
6 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 7/17/2024 in #german-support
Drucker druckt nicht auf der Gesamten Druckfläche 400mm
ist der slicer richtig eingestellt ? https://github.com/HelgeKeck/RatOS/blob/documentation_v2.1/site/docs/slicers.md
2 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/26/2024 in #fix-my-printer
Option 'pin' in section 'probe' must be specified - after update
For me that was the easiest way ... and the new 2.1 RatOS is very nice and easy to set up ...
10 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/26/2024 in #fix-my-printer
Option 'pin' in section 'probe' must be specified - after update
I dint continue to troubleshoot that ... i just made a fresh insatll with the RatOS 2.1 and it is working fine now
10 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
its printing now again :ratrig_heart: i guess I just keep this override for now ... at least i know now where I can/need to change it if needed ... fantastic job Mikl :ratrig_heart:
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
so means i could go back to configurator and just use the "Digital PWM on 4-pin port" and my changes like inverting axes will stay ?? yes i had to reduce the max power otherwise i had to chnage all my fan settings in the slicer cause the eFuse was triggered at max power ... im using this super fan from which Helge was showing some time ago but the fan need to much power
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
i really like the new configurator ... so far i got all running ... only my part cooler doesnt work ... need to check my old config maybe
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
yes sure ... thx will go for that one ... thx a lot for your help
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
it seems like i have to make a fresh install ? when i updated yesterday nearly all showed corrupt so I did hard recovery one by one until they wére all updated ... seems like it was a bad idea
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
okay uncommended #[include RatOS/homing.cfg] now <. Section 'gcode_shell_command generate_shaper_graph_x' is not a valid config section
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
I have no idea what happened ... but at least you gave us a workaround if it fails again .... short question : what value should be minimum_cruise_ratio ?
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/27/2024 in #ratos-support
NetworkManager not working after update
hi thx for your response ... i just started again the printer and just by miracle he connected without issue ... this is very strange as i did that i then afternoon for like 20 times ... very strange
70 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/26/2024 in #fix-my-printer
Option 'pin' in section 'probe' must be specified - after update
i have another issue now ... since i made all the updates i get following errors on klipperscreen and cant connect anymore : 1. failed to initialize sdbus 2. failed to start NetworkManager service
10 replies
RRCRat Rig Community [Unofficial]
•Created by DOAmatrix on 5/26/2024 in #fix-my-printer
Option 'pin' in section 'probe' must be specified - after update
10 replies