Kano
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Ok. Before I go and do a first layer print, Helge mentioned something about my z offset being negative. Is there something I need to check before first layer print and babystepping?
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Ok. So just go ahead and run BEACON_RATOS_CALIBRATE and VAOC after?
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Setup Wizard, Dashboard, Motion Visual Calibration, and Realtime Analysis all seem to work just fine
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Yea.
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
I updated it at the same time
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
the update didn't fail. Should I worry about it?
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
The only reason I did the manual route was to do the VAOS thermal expansion calibration on step 3
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
From my understanding of the instructions on beacon calibration BEACON_RATOS_CALIBRATE is the automated process of running through steps 1-5 which I did manually. If that is not correct, that may be my problem
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Anyone have a fix for this? I'm not sure how to move forward from this?
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Yup. It has been disabled
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Isn't that disabled by default? If not, I guess I can try to specifically disable it.
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Sorry That wasn't all of it
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Here is the console_history strip to readable text if that helps
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Isn't it in the debug zip? console_history.json. I can screenshot it, but its a lot of information to screenshot. Is there a better way to get it?
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Here is the debug zip after running through the beacon calibration again with ENABLE_DEBUG on
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
Those wait times are in there currently. I will restart the process of calibrating beacon with ENABLE_DEBUG on and post that debug.
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 11/6/2024 in #ratos-support
SAVE_Z_OFFSET always saves to beacon model offset
50 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 10/21/2024 in #fix-my-printer
New machine vcore 4 machine with idex installed before commissioning
Thank you!
10 replies