jgeo_
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
After many attempts adjusting frame and gantry points (as described in manual) I managed to do the best in Heghtmap calibration and get the range down to 0.14. Later I also did a test print to try to set the Z offset. It went quite ok.
17 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
So, after some days wait, I've received a new replacement Toolboard EBB42 v1.2 from RatRig (thanks a lot!). After replacing, and lot of playing with setup, updates, etc. I finally managed to make it working and the temperature was shown correctly after startup. Somehow I was also missing the Toolboard configuration (not in the instructions, I followed?), and the need to tell where the X/Y stops are connected, etc. After setting all that correctly, it finally all worked from HW and electronics point of view.
Now I try to calibrate the Heightmap, I'm getting quite bad values, like 0.341 range, the front side is up by 0.08 and the back left corner is down by 0.26.
17 replies
RRCRat Rig Community [Unofficial]
•Created by Oldschoolhippie on 9/23/2024 in #ratos-support
ADC out of range
Just received my board 2 days ago and I'm going to install it. Happy to hear, the problem is away in your case!
55 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
So, I get similar values measuring the resistance, when I heat it up a bit, it goes up immediately and when it cools down, it goes slowly down.
I did not try yet to bypass the values in config to override it.
17 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
Uff, ok, I will re-check the cabling and try to measure the resistance first. So it's rather about thermistor (or EBB42 board) rather than MCU...
Thanks, I will follow the other thread as well.
17 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
___
And RatOS.cfg contains the following entry:
[mcu]
serial: /dev/RatOS/btt-octopus-11
[temperature_sensor Octopus_V1.1_F446]
sensor_type: temperature_mcu
[adxl345 controlboard]
cs_pin: PA15
spi_bus: spi3
- Is that serial: /dev/RatOS/btt-octopus-11 correct?
17 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 9/28/2024 in #fix-my-printer
Klipper reports: ERROR
When I open RatOS.cfg and see Devices, I have for USB:
Beacon 04d8:e72b
Beacon RevH Microchip Technology, Inc.
usb_location 1:4
serial D4DEEA8E5154364134202020FF142621
class Communications, Abstract (modem)
protocol AT-commands (v.25ter)
Klipper 1d50:614e
stm32f446xx
OpenMoko, Inc. Klipper 3d-Printer Firmware
usb_location 1:5
serial btt-octopus-11
class Communications
Klipper 1d50:614e
stm32g0b1xx
OpenMoko, Inc. Klipper 3d-Printer Firmware
usb_location 1:3
serial 050026001250425539383920
class Communications
And for Serial:
USB
cdc_acm
ttyACM2
Device path
/dev/ttyACM2
Path by ID
/dev/serial/by-id/usb-Klipper_stm32f446xx_btt-octopus-11-if00
Path by hardware
/dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.4:1.0
USB
cdc_acm
ttyACM0
Device path
/dev/ttyACM0
Path by ID
/dev/serial/by-id/usb-Klipper_stm32g0b1xx_050026001250425539383920-if00
Path by hardware
/dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2:1.0
USB
cdc_acm
ttyACM1
Device path
/dev/ttyACM1
Path by ID
/dev/serial/by-id/usb-Beacon_Beacon_RevH_D4DEEA8E5154364134202020FF142621-if00
Path by hardware
/dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.3:1.0
17 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 8/26/2024 in #fix-my-printer
Issue installing RatOS 2.1 on Raspberry
Works fine, thanks!
6 replies
RRCRat Rig Community [Unofficial]
•Created by jgeo_ on 8/26/2024 in #fix-my-printer
Issue installing RatOS 2.1 on Raspberry
Wow, I overlooked that, thanks a lot, will try right now! (It's getting late and getting tired here 🙂 )
6 replies