CookieJunky
RRCRat Rig Community [Unofficial]
•Created by MurmelMannen on 12/14/2024 in #fix-my-print
Wobbly/uneven walls
Dual drive gears are the fault for this most likely.
I guess orbiter 2.5. Should be better or hextrudort. Waiting for the new orbiter to try out
3 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
Hi, did not update yet. I redid the toolhead and tuned pressure advance. It was by a lot incorrect. Don't know how, but maybe an old setting when.i used HF adapter. Belts tightened correctly and somewhat decent and correct Y axis input shaper. X is a mess I'm ashamed even to show, but now the input shaper at least somehow works and prints got a lot better. Still some ghosting. I recall my toolhead needs just a total swap, either to ratrig new one or entirely go with hextrudort setup. Something vibrates there and I secured literally every part that can be secured and it šis not.help the x axis input shaper at all
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
Addition: I dissassembled everything, cleaned out the carriages, relubed them with silicone oil, printed a new pair of xy joiners, because i saw that something was off when assembling back. This repair did something incredible (onlky to Y axis). This can be sen in the input shaper test with mzv up to 25k accel. Which is crazy. However, the X axis is a mess. The print - coron cube looks like this. X was dissassembled and assembled anew. maybe it needs parts reprinting as well, but i cannot see why. Everything is tight as hell.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
But as I said. Its overall a problem in all prints. They come out quite bad. I see ringing, but my profile does not help much. Nor MZV nor 2hump-ei. I have a nozzle mounted accel only, because the others broke.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
I see. Well then. Here i enclose the stl and also the gcode. They might be a bit different in spacing as it is not the final design. I suck at modeling
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 11/27/2024 in #fix-my-print
Uneven texture 3.1.
Its not the stl. Every print looks like this - like shit.
Here is a photo of another thing
14 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
And I got another clog in the morning
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
Hey this one. Yes!
I get blobs of filament right above the heating zone which gets stuck but the last move it seems is enough for me to break that string apart
And the only way to take it out is from the nozzle side, poking a hez wrench heating the material from underneath
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
Well i had a couple of clogs after. One very nasty, but due to wood filement. It all comes down to extruder not pushing enough material out before doing those retractions back and forward and final retract. I must say, this new macro makes the tip so much better, but it also makes the tip sometimes a bit bigger, so even it clogs the extruder, so that it can not be released: A: without shifting the knob to make gears further apart B: dissasembling the xtruder. As i was about to install back ratos 2.0 macro someone sent me in discord, my printer got spooked and does not clog at this time, even though i have not changed a single thing. It has been several days and each and every filament swap i do is good. The furthest i went was A option of shifting gears 10 minutes ago. It is still some kind of magic.
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
The guy installed ratos 2.1. not changed the toolhead. The ptfe tube whilst is a possible problem, but def not in this guy's case. It may be my case, but it will be over a month till i get the new ptfe to install and check.
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
I am still experimenting and waiting for this to happen again to reconstruct the situation.
It could be something with the macro, but until this happens again and I document the situation, I can only tell that something is off.
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
Well I kinda checked. It all falls in line with what it needs to look like. I cut a fresh ptfe tube a little bit better and I will see. It should.not be hardware related, as this occurred with the RatOS 2.1.
I have some free time where I do.not.need to print stuff actively, so I'm kinda beta testing the new system
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
Nope, I was quick to judge. It was clogged, but not at the hotend and heartbreak part. It was clogged in the extruder
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
@miklschmidt Well, the macro for the UHF it seems is incorrect. I installed the adapter and it clogged right away.
20 replies
RRCRat Rig Community [Unofficial]
•Created by CookieJunky on 7/27/2024 in #ratos-support
Rapido UHG clog
MVP. I did not yet print out the fan duct, so good to know on when to configure for the uhf!
20 replies