AllSparkII
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 4/23/2024 in #fix-my-printer
Klipper fails after hard Recovery
When trying to reach that page.
Afterall I did two full reinstalls. After the first one I made all the Updates and ran into the same problem.
On the second try I left out the Klipper and RatOS Updates and waited for new releases before updating. Not a satisfying solution, but worked for me and narrowed the origin of the error down ^^
6 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/16/2023 in #fix-my-printer
Ratteling Noise on diagonal moves (V-Core 3.1)
From what I can feel the vibration is strongest on the pinda probe, fan horn and probably the nozzle (can't confirm tho, didn't touch that xD). Fans are clamped down really well, no noise there.
The whole movement system starts shaking with these moves - you can feel it on the Belts and the whole EVA System. I believe, as mentioned, it's worst on the lower half.
Switched Stepper drivers today - that made it a little better. Used other motors (no effect), turned down the stepper Amperage (little better). Rechecked the whole Hotend Assembly - worse again.
Probably gonna reprint the whole EVA System, if asychevs Ideas don't work out tomorrow 🥲
16 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/16/2023 in #fix-my-printer
Ratteling Noise on diagonal moves (V-Core 3.1)
Quick update from me - Lubed all rails according to the linked video. No difference. Put extra Grease on the rails where the print happens even more (way more than pictured) - no difference.
Disabled Stealthchop in the printer.cfg - it got worse...
Part of the ratteling was caused by the "super Pinda" - the super high pitch overtone is gone. But the rattle still mostly persists.
16 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/16/2023 in #fix-my-printer
Ratteling Noise on diagonal moves (V-Core 3.1)
Most PTFE Based Bearing Greases should be fine (according to the reasach I did after this conversation). Look for Temperature resistance over 90°C or higher when having the printer enclosed. The Grease should not have abrasive contents like Graphite based greases!
16 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/16/2023 in #fix-my-printer
Ratteling Noise on diagonal moves (V-Core 3.1)
There is a very light coating of sewing machine oil, applied with a paper towel - I would say thats sufficiant, but I am by no means an expert on linear rails 😓
The transport coating was removed with Isopropanaol.
16 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/16/2023 in #fix-my-printer
Ratteling Noise on diagonal moves (V-Core 3.1)
They're new and lubed like the instructions told me to. The printer now has ~10 hours of runtime, most of it was setup. This is one of the first prints ^^
And it does not rattle when doing moves in only X or Y direction 🤔
16 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/3/2023 in #ratos-support
Octopus 1.1 detected but unrespnsive
No problem at all, thank you so much for the quick answers and fix for my problem!
11 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/3/2023 in #ratos-support
Octopus 1.1 detected but unrespnsive
That was my exact problem, thank you so mutch! I was fiddeling around for two days now, not making any progress 😵💫
But the behavior was wired afterwards too - the MB was found and okay, then it disconnected, then it was fine again. This loop took around ~5 Seconds and was endless. I was fast enough in one of the rounds to just klick "next" and it went away. Do I need to refresh the firmware.bin on the pi for safety or is that normal? Seems to be running fine for now ^^
11 replies