lary9920
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
I found a wiring issue and pretty sure it explains the fan behavior. Thanks for your help.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
I'm at work. I'll test these things when I'm home tonite.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
T0 and T1 go to 100% when Klipper boots, then both go to 0%. The file I'm printing uses only T1. So I start the file and both heads move to the middle and T0 goes to 100% but T1 stays at 0%. Then when the print startes, T1 is printing, which normal fan control, but T0 moves over to its park position (after beacon, etc) and goes to 100% constantly.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
Other than that - thanks very much!
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
I'll mark it solved again. I will mention one other weird thing. My T0 fan goes to full 100% during the whole print, even though I'm printing with T1.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
Thanks - it does again start a print. Re-uploading the file was the issue. It does throw up a post-processing message as well.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
I can try to get to this. I haven't set it up to print directly, and it may take me a bit.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
From the console.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
It can't resolve the path to the files.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
Apologies - I had to mark this one as not yet solved. I still can't run a print. Getting a new set of errors when I try. I'll post a new debug.zip and I try the sudo update.
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
My is booting again. Thanks very much!
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
Can confirm that the error only appears to occur if that Klipper update hasn't been run yet. And, it only appeared for me after the full reboot like @Dor_Amboss .
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
running it now
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
One just popped up for Klipper on my machine page
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 12/19/2024 in #ratos-support
Latest update rendered Vcore 4 nonfunctional
Where/How do I find the debug.zip that is needed?
62 replies
RRCRat Rig Community [Unofficial]
•Created by lary9920 on 11/17/2024 in #fix-my-printer
Layer Shift Problem
Thanks. The motors sound fine and I agree, I started thinking maybe a driver was overheating or something. But I am now leaning toward loose belts and skipping teeth. I watched it happened and it starts with a ‘big’ travel move in the opposite direction of the infill line it just laid down. Kind of like excessive jerk. It’s a diagonal move which may be why the shift is diagonal as well.
Also weird that it happens to both tools. Seems like it would need to be Y in that case. Could be missed steps in Y, but unless they’re exactly equal I don’t understand why it wouldn’t start to affect the gantry.
My X belts are a LOT looser than the hybrid belts. So maybe time to venture there.
7 replies