NULL
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
This is also the reason that i disable the motors because then you need to home the machine and it will place the Z in a safe position
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
I set my Z to -7, just note that you really need to be carefull if you place your Z at 0 or negative
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer

301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
301 replies
RRCRat Rig Community [Unofficial]
•Created by Milkman3407 on 4/19/2025 in #fix-my-print
Over extrusion (maybe?)
5 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
You can change it settings from your printer config file
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
I have a new version of the macro that is a bit better and more friendly to use
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
No i use that for 0.6 sorry
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
This will help to catch inconsistencies because only T0 is compensated
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
What i do is set my first layer to 0.5mm with 0.8 to 0.85 width for it
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Sure is it also a 500?
301 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Be a aware of the IDEX MIRROR in my start code
301 replies
RRCRat Rig Community [Unofficial]
•Created by Mat on 4/17/2025 in #fix-my-printer
Beacon probe Z-offset is consistently too far from build plate
Even this can result is heat expansion on the gantry
26 replies
RRCRat Rig Community [Unofficial]
•Created by Mat on 4/17/2025 in #fix-my-printer
Beacon probe Z-offset is consistently too far from build plate
i think they are back in stock now
26 replies
RRCRat Rig Community [Unofficial]
•Created by Mat on 4/17/2025 in #fix-my-printer
Beacon probe Z-offset is consistently too far from build plate
Read also into this if you do print with larger first layers times you also need to have the gantry expansion in mind https://discord.com/channels/582187371529764864/1360247935496884265
26 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
I soaked at 80 for 1h30 and isn't working
301 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/19/2025 in #fix-my-printer
camera setup logitech c920
Or communicate with the printer trough ethernet
38 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/19/2025 in #fix-my-printer
camera setup logitech c920
So two things check your wifi and see if you can increase throughput
38 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/19/2025 in #fix-my-printer
camera setup logitech c920
I have made a capture at work and in a span of 9hours the camera streamed data was 230GiB
38 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/19/2025 in #fix-my-printer
camera setup logitech c920
When I connected trough ethernet is was all fine
38 replies