Toros
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
ok. i will do it when the update comes in ratos. :ratrig_heart:
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
using x rail was a very good advice. ok i will do that. thanks alot :mildpanicintensifies:
also i did beacon update now. but the auto calibration offset is not that accurate and i have ratos 2.02
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
I put 1 kg of filament model today. I will do it in 1.5 days. :))
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
You're talking about the rails on your Y-axis, right?
I'll loosen and tighten them, then. :mildpanicintensifies:
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
I went back to the stock gantry, warmed up the plate for a while and loosened and tightened the screws. the result is much better than before, but this time there are waves. will these waves cause problems?
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
actually this is not that bad, but i need check my screws
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
Actually, I don't seem to have sagging, but bending in the opposite direction. Since my 9mm rail joiner has a screw on the inside of the joiner, I plan to open it after it has been pressed for a while 🙂 but my bedmesh is at 0.6s :mildpanicintensifies:
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
yes, this is probably my problem. i couldn't get any print for a long time. i'll manage a little more, open the joiners, tighten the screws from the beginning and try. if the problem is not solved, i'll switch to the new gantry. 😅
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
I only use abs for the sculptures I make. the maximum bed temperature is 110 degrees. will this affect it again?
I mean, when you say high temperature, how many degrees are you talking about?
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
literally...😅 I will look into the bowing problem after a couple of off and on and new print trials. tanks again!!
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
I'll lose all the screws on the gantry one more and try again
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
sure
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
heyy!
i understand. i will do what you said and try it with variable_calibrate_bed_mesh turned on. as far as i remember i had such a problem in pinda but i solved so many problems that i honestly don't remember exactly.
and tomorrow I'll tell you what happened. Thank you very much
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 5/22/2024 in #fix-my-mesh
IMPOSSIBLE Z- OFFSET,VC 3.1 /500
the problem is exactly this. After restart, HOME-->Z-TILT-->BED-MESH-->BEACON_CALIBRATE(or with babystep)-->SAVE_CONFIG I have no problem working with the saved mesh profile until these settings restart, but after restart if I BED-MESH again with the z-offset set as before, it adjusts the new profile to the offset of the previous one and therefore the plate comes out higher. what is the reason for this?
38 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 3/14/2024 in #fix-my-resonance
I wonder if the Hertz is low? (v-core 3.1/500)
I have beta v2 toolhead and stock gantry 🙂 but I've changed that tensioners with heat insert tensioners.
9 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 3/14/2024 in #fix-my-resonance
I wonder if the Hertz is low? (v-core 3.1/500)
yeah they are looking good now :))
9 replies
RRCRat Rig Community [Unofficial]
•Created by Toros on 3/14/2024 in #fix-my-resonance
I wonder if the Hertz is low? (v-core 3.1/500)
oh thanks 🙂 I got some prints and they are looking good
9 replies