Tom Turbo
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
hope that solves the issue with the Z Offset tho ^^°
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
never thought that little turd could be trapped air, thanks a lot for the info i tcould be trapped air :b
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
thanks for your time mate :3
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
2 things i leaned,
X is Y and Y is X in this Graph
some times the weird stuff works out
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
it is quiet frustrating :/
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
either i wait until it gets out of RC status or Nuke everything i have on the printer and start with a new Config
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
started with 2.1.0 RC3-6 the last days, today's morning upgraded to RC3-8 without any change
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
also have a problem where my Z Offset is not saved from print to print, saved config but still 0.038 instead of -0.060, i think that is not something tied to this problem but perhaps there is something that contributes .-.
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
i have a small spot that bulges a tiny bit but thats centered to the front, don't see anything in the graph
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
it did not install is as good as i wanted but wiped the bed the bed with IPA before, also was wearing Gloves to not get any dirt or grime on there while installing it
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/12/2024 in #fix-my-mesh
Mysterious Peak
there is nothign between the magnetic sheet and the build plate but i remember after some thinking i crashed the bed in the commissioning (because I didn't read it through carefully enough), build plate has some light scratches but nothing i would be worried about
24 replies
RRCRat Rig Community [Unofficial]
•Created by Tom Turbo on 10/6/2024 in #fix-my-printer
Problem/Errors: Commissioning Guide | Step 2 - Build plate prep.
i have to admit, no i did not follow those docs but it worked perfectly 🙂
4 replies