SwissStar_BL_2
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
No worries, we all started somewhere
18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
Just go trough the configurator once again
18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
Just to clarify: you followed the instructions on the RatOS site?
18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system

18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
Or add it respectively
18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
If yes, than remove the
!
in front of the 18 replies
RRCRat Rig Community [Unofficial]
•Created by 6e756d62657273 on 4/6/2025 in #fix-my-printer
RatOs operating system
Does it turn off when you set the fan to 100%?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Robee on 3/9/2025 in #ratos-support
Set heat soak time in the slicer?
Both
18 replies
RRCRat Rig Community [Unofficial]
•Created by Robee on 3/9/2025 in #ratos-support
Set heat soak time in the slicer?
Did you use the exact line like here:
https://discord.com/channels/582187371529764864/1348285664369705000/1350714247083986944
If yes, do you have the gcode_macros RatOS section in your printer.cfg and do you have the variable set there?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Robee on 3/9/2025 in #ratos-support
Set heat soak time in the slicer?
See also here: https://os.ratrig.com/docs/configuration/macros#variables
18 replies
RRCRat Rig Community [Unofficial]
•Created by Robee on 3/9/2025 in #ratos-support
Set heat soak time in the slicer?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Numb3r_0ne on 1/28/2025 in #ratos-support
beacon 3.1 wrong offset
Put this in the overrides:
Change the values according to your setup, these are for my 400.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ls on 1/14/2025 in #fix-my-printer
Extruder temperature not right
Check what thermistor you have and change it accordingly in RatOS. Sounds like a wrong thermistor config
7 replies
RRCRat Rig Community [Unofficial]
•Created by sensitive-blue on 1/6/2025 in #german-support
RatOS
Top👍
16 replies
RRCRat Rig Community [Unofficial]
•Created by correct-apricot on 1/6/2025 in #german-support
RatOS
Das wäre die sauberste Lösung
16 replies
RRCRat Rig Community [Unofficial]
•Created by harsh-harlequin on 1/6/2025 in #german-support
RatOS
Das sollte nicht so sein, die Änderungen werden im Normalfall direkt in die printer.cfg reingeladen und abgespeichert. Lad mal bitte deine printer.cfg hier hoch, dann können wir uns das anschauen
16 replies
RRCRat Rig Community [Unofficial]
•Created by fascinating-indigo on 1/6/2025 in #german-support
RatOS
Wie Alex sagt, alles in die printer.cfg rein
16 replies
RRCRat Rig Community [Unofficial]
•Created by other-emerald on 1/6/2025 in #german-support
RatOS

16 replies
RRCRat Rig Community [Unofficial]
•Created by yammering-amber on 1/6/2025 in #german-support
RatOS
Was für Änderungen und in welcher Datei?
16 replies