Shuni
RRCRat Rig Community [Unofficial]
•Created by Shuni on 6/14/2024 in #ratos-support
VC4-RatOs 2.1 48V 5160T Pro Unable to write tmc spi '...' register GLOBALSCALER
:vibing:
31 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 6/14/2024 in #ratos-support
VC4-RatOs 2.1 48V 5160T Pro Unable to write tmc spi '...' register GLOBALSCALER
nur die 24v 2209 brauchen den einen jumper
31 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 6/14/2024 in #ratos-support
VC4-RatOs 2.1 48V 5160T Pro Unable to write tmc spi '...' register GLOBALSCALER
31 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 6/14/2024 in #ratos-support
VC4-RatOs 2.1 48V 5160T Pro Unable to write tmc spi '...' register GLOBALSCALER
mach mal alle 48v stepper raus und mach ein bild vom board
31 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 6/14/2024 in #ratos-support
VC4-RatOs 2.1 48V 5160T Pro Unable to write tmc spi '...' register GLOBALSCALER
ja und tripple check die Jumper wenn du das tmc problem hast
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 1/10/2025 in #fix-my-print
VC4 500 Extrusion Issues with PETG
Try an easy fix - limit the max volumetric speed for the material to 15mm³/s or even less
21 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 1/10/2025 in #fix-my-print
VC4 500 Extrusion Issues with PETG
oh and partcooling can be too high
21 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 1/10/2025 in #fix-my-print
VC4 500 Extrusion Issues with PETG
But I see
- way too fast printing
- maybe wrong PA
- first layer might be too close
- (maybe even wrong temperature)
21 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 1/10/2025 in #fix-my-print
VC4 500 Extrusion Issues with PETG
is that first image there still the first layer on the bottom of the image?
21 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
118 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
where can I find the default values for restoring?
118 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
I checked the cable and everything was fine. Copied the config from T1 to T0, edited to make it T0 again and now it works.
very weird. Especially because I copied T1 from T0 :derp:
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
thats what I did already, but will try tomorrow again. And I'll check cable with multimeter for conductivity. If those two things are not working, I'll probably need to replace the sensor
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
PB9, same. No reaction
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
tried PB8, also no reaction. Maybe the sensor button is dead?
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
Crimp is perfect, no issues there
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
Yep, works fine on the 2nd Toolhead. I'll investigate for bad crimps :kellysalute:
(they are both equally wired, as I did both at the same time)
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
Will load the 2nd toolhead with filament to check if its working there
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
correct, but the sensor starts blinking blue
40 replies
RRCRat Rig Community [Unofficial]
•Created by Shuni on 11/14/2024 in #ratos-support
Smart Filament Sensor Unload button Action not triggering
or do you need another page?
40 replies