Hajoto
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
If somebody is interested and maybe have the same issue: Problem solved, with new probe end-stop shows desired results with triggered and open.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
Update from my side. Raspi was installed new, firmware flashed again (with correct board), wiring was checked again with the same result: LED works as desired. I've seen that this just means that GND and 5V is connected correctly.
Last check was with a different probe on the BL-touch pins and the endstop-check shows the desired result. Unfortunately because of the geometry this probe cannot be installed.
So, I will order a new probe and hopefully then it works.
Thanks for your support.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
Board was changed in printer.cfg and firmware flashed to Octopus V1.1. I will try to start from begimming this weekend. Maybe I made a mistake in the setup and triplecheck the wiring again.
Your help is much appreciated.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
J40 pins don't work either.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
Double checked the wiring and it now looks better. According to the LED the probe itself works.
Would it make sense to use the sensor pins (J40)? Or z-endstop pins?
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
unfortunately no change
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
I will try
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
yes, with metal and whitout metal no change.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
hm, firmware flashed and board corrected in printer.cfg. Unfortunately no change for the probe. Still LED works correct, but no function with endstop check.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
I also noticed that.
To stupid, that I did not check the board, just thought that the board is the one which was mentioned on the Ratrig homepage. Maybe the reason was the red color of the cover for the power cables, on my other Octopus V1.1 board it was orange 😂
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
but I've seen that in the RatOS installation guid - I will check there
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
Thanks for your support, but this means I have to flash the firmware on the board as well?
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
OK, then my mistake - obviously I have no pro version. I will change the title.
Nevertheless thanks for your support.
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
40 replies
RRCRat Rig Community [Unofficial]
•Created by Hajoto on 2/15/2024 in #ratos-support
Octopus V1.1 (F446) SuperPinda Probe Always Triggered on
I don't have these connectors. I followed the Dozuki installation guide and did the wiring accordingly. The probe itself seems to work.
40 replies
RRCRat Rig Community [Unofficial]
•Created by rising-crimson on 12/2/2023 in #ratos-support
Octopus Max Ez SuperPinda Probe Always Triggered
I use the SuperPinda, bought from Ratrig:
https://ratrig.com/electronics/probes-limit-switches/rat-rig-superpinda-probe-by-pepperl-fuchs-inductive-5vdc-sensor.html
13 replies
RRCRat Rig Community [Unofficial]
•Created by flat-fuchsia on 12/2/2023 in #ratos-support
Octopus Max Ez SuperPinda Probe Always Triggered
Hi miklschmidt, thanks for your response. I have a Octopus Pro board (F446) and wirded the probe according to the Dozuki installation guide. When I compare the colors of the wires (in your image), the probe was connected correctly.
Do you have any other recommendation?
Or would it be better to install the probe on an endstop port?
13 replies
RRCRat Rig Community [Unofficial]
•Created by correct-apricot on 12/2/2023 in #ratos-support
Octopus Max Ez SuperPinda Probe Always Triggered
Hi Anon13, I have the same issue, but don't understand your solution. Could you probably explain? When I checked the pin configuration in your and my boards configuration, there is no such pin "înd_probe_pin" specified.
Any help would be appreciated.
13 replies