Korisnik Comments - Answer Overflow

Korisnik

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Yep, the fan is no good. Which is the best one to get since I'm already in the market for a new one? Should I just get a cheap one from Aliexpress?

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Got it. Don't need to change any settings then?

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

There's a wiring diagram online no?

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Yeah 😄 Thanks a bunch, you and @RRBender are lifesavers.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Heh, guess we solved the issue then

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Because when I set the ''fan'' to any percent, the 5015 is still off.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

I have a quick question about the fans in ratos.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Got it, thanks.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

But do you personally think a problem like this can be avoided with a stronger fan?

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

Ah, alright.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 2/26/2024 in #fix-my-print

[Overhang issues(?)] What's causing this? The distance from the nozzle to the bed is spot on.

This is the stock fan that came with the V-Minion. All other settings are default. Should I switch to a different one?

32 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 1/24/2024 in #fix-my-print

Curling issues on my V-Minion

Yeah the more I'm trying to figure it out the more I'm confused. Why would the fan be enabled for smaller layers but disabled for the ones that take more time?

24 replies

RRCRat Rig Community [Unofficial]

•Created by Korisnik on 1/24/2024 in #fix-my-print

Curling issues on my V-Minion

Says on the PrusaSlicer page: If the layer print time is estimated below this number of seconds, the print fan will be enabled and its speed will calculated by interpolating between the Min and Max speed.

Gaming

Programming