DapperDangus
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
I was fortunate enough to have a 24”/60cm machinist caliper too which allowed me to adjust all my extrusions precisely. Made sure all my top extrusions were flush then used the caliper to make sure all of the middle extrusions were equal distance from the top. It’s better than a tape measure/ruler since I can lock it into place.
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
Oh you’re referring to the YouTube video haha. Man, this printer is racking my brain.
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
There is always a perfect meme for the occasion 🙃
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
still got some stuff going on down the line but im calling that a bit of a win tonight. Will work on it more tomorrow
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
Yeah made sure I got it on the flat part. Last night I tried resetting it on the flat part again. I’m gonna go through this video tonight and see where it gets me. I’m hoping I don’t have any of my stacks too tight. https://youtu.be/cOn6u9kXvy0?feature=shared
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
Good deal thank you.
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 9/10/2024 in #fix-my-resonance
Could use some guidance on the psd graphs. VC4 500
I looked up a video for deracking. I did some of those things but could definitely do some more. I definitely feel a resistance towards the back. I will try this out when I get home.
Belts are exactly the same though, double and triple checked them each time I made a cut. Also the belt teeth are lined up on the exact same clamp teeth.
On the deracking subject as well. That’s probably my issue with my belts riding up and down the motor pulley as I move the gantry back and forth. Plus I have some resistance towards the back.
20 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
Yeah plus you would expect the opposite actually I think. Those corners would need to come up if they were sagging, not go down. Might be possible to use something to pull each corner towards each other. It would go under the bed and maybe clamp to the sides. Idk, probably not worth messing with it that much. I’m not gonna really try and fix anything too much till all the panels are on and it’s in a finished state.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
Yes, having the build plate and magnet on there helped quite a bit. Although as soon as I heated my bed to 80C my variance went back up to .256 🤷 is what it is. I think the corners are just gonna be like that. Considering the weight of the plate, the dips are right where there is no support.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
And.... I caught my unicorn everybody :chefkiss:
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
I think it's pretty good, just something is up with those back corners. Maybe I need to stand on my plate on a flat surface to take the bow out lol.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
Wanted to start with equal since the ones I cut wouldn’t be long enough for proper testing.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
Nice looking forward to reading it today. My big issue with the equal belt thing is telling people to completely rebuy and redo their belts. I have quite a bit of extra belt so I’ll still be doing the print test comparison before I install IDEX.
139 replies
RRCRat Rig Community [Unofficial]
•Created by DapperDangus on 8/29/2024 in #fix-my-printer
Clicking stepper motor.
I mean I’m sure they aren’t actually duck footed as evidenced by the holes now lining up correctly. But what I did was screw the entire right rail down then attached the x gantry to it.
Next, I aligned the left carriage screw holes and tightened the first few rail screws while the gantry sat upfront against the bumpers. Moved the gantry and carriages to the back. Used those alignment brackets to hold the right side in place then I loosed all but the first screw on the left rail. Turned it outwards.
This almost got me there but it needed a tiny bit more so I tightened the left side down and did the right side in the same sort of way.
Very interested to see the difference in my mesh. I gotta do a lot to get back on track though as I need to basically disassemble the entire tool head to swap the carriage out. So while I’m at it, gonna make my belts equal length this time among a few other things.
139 replies