Rhymnoceros
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/23/2024 in #fix-my-printer
extruder not heating correctly "verify_heater" issue where it sits at 150 C
that looks like its worked thankyou!!!!!!
4 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
will do thank you
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
I think i need to reset my config and see if it picks up the correct stuff, but I don't know how to reset it
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
after ending up with everything in the config file, I tried to reset it by reflashing my board but it came back with my current messed up config
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
now its back to sitting at 150-160 C with a 0 target
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
so I copied the cotroi from the first image into my config file, then it demanded that pid_kp need to be specified
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
which had all of the correct settings for me, i then copied this into my config file, but klipper then kept mentioning that control needed specifying and wouldn't boot until it was specified....
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
scratch that I just ripped out the plug i need to rewire it quickly
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
I'll take a pic and share but I've messed it up a bit now
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
hi @Beluga @Seriosha , I have the same problem but in my printer config file my extruder section is looking different. was the image you shared Beluga of you extruder section (row 335) in you printer.cfg file? If so I think I need to reflash my board, if not where is it?
41 replies
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/9/2024 in #ratos-support
DFU not detected, BTT board not detected, can't flash my BTT Octopus v1.1
ah okay, thank you. I'll carry on setting up mainsail and wiring up my panel. thank you both
34 replies
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/9/2024 in #ratos-support
DFU not detected, BTT board not detected, can't flash my BTT Octopus v1.1
the last image I shared, the board is detected when I try and flash it, but the configurator says its unresponsive, I'm hoping that's normal as there's nothing attached to the board?
34 replies
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/9/2024 in #ratos-support
DFU not detected, BTT board not detected, can't flash my BTT Octopus v1.1
one question in case either of you see this, do I needc to worry about the octopus board being unresponsive
34 replies
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/9/2024 in #ratos-support
DFU not detected, BTT board not detected, can't flash my BTT Octopus v1.1
I think I'm done so I'm going to mark this as solved, thankl you both for the support
34 replies
RRCRat Rig Community [Unofficial]
•Created by Rhymnoceros on 2/9/2024 in #ratos-support
DFU not detected, BTT board not detected, can't flash my BTT Octopus v1.1
5. go to the configurator, reset the control board and now when I check the DFU option it finds my Octopus board and I can DFU boot (i do have all the jumpers advised attached)
34 replies