Heretic_Infidel Comments - Answer Overflow

That was my thinking as well - just start from a blank slate. Have had to rebuild my printer anyway so already happy it is up and running and calibrated. Reflashing and copy-pasting my config back and re-doing some calibration work is easy enough

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Tried looking up what I did but couldn't find it anymore in the ratos-development pinned posts. At the time what I did was follow the guide to move to the branch that allowed for th use of 2.1 - RC1 and have been following that branch since.

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Thank you for the help either way. A warning message might indeed be good reminder for those who don't print daily 😄

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

It's a hobby machine and was onthe dev for the 2.1 before the summer. THen moved house and never had any problems before. But it works now. When I have some time i\ll do the rollback to the normal

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Ah - thought that might have been the case. Let me try and update. Otherwise I can always roll back to the official branch

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Could be - This install is still from the release of RC1. Software update is of the opinion that I am ratos-configurator v0.0.0-349-gfdaac5e6-inferred Repo not on offical remote/branch, expected: origin/v2.1.x-deployment, detected: origin/dev-deployment

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Did a clean install of Prusaslicer, double checked the config from the documentation. Result is still a crash 10:20:28 $ ENABLE_DEBUG 10:20:28 RatOS | DEBUG: Debugging enabled. 10:21:18 Post-processing started Processing Shape-Box_PLA_QUALITY_0.20mm_Nozzle_0.4_VC3_54s.gcode (0.05 mb)... 10:21:20 // Klipper state: Shutdown 10:21:21 File opened:Shape-Box_PLA_QUALITY_0.20mm_Nozzle_0.4_VC3_54s.gcode Size:0 10:21:21 File selected 10:21:21 // Unhandled exception during run // Once the underlying issue is corrected, use the // "FIRMWARE_RESTART" command to reset the firmware, reload the // config, and restart the host software. // Printer is shutdown 10:21:21 !! Unhandled exception during run 10:21:21 // Unhandled exception during run // Once the underlying issue is corrected, use the // "FIRMWARE_RESTART" command to reset the firmware, reload the // config, and restart the host software. // Printer is shutdown 10:21:21 !! Unhandled exception during run 10:21:21 Done printing file

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

It goes into 'pre-processing' and then the crash

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Nope - instantly crashed

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Smallest I could think of - 30x30x0.2 box created in latest version of super slicer. Logs attached.

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

Just tried some old files that printed succesfully in the past and same problem.

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 12/9/2024 in #ratos-support

Pre-processing will cause firmware restart

I've tried a couple of different Start G-Code and the result is always the same failure state. Print started either as a direct upload from the slicer or a manual export & upload For PS and SS I've tried the defautl profile, as well as what is on the os.ratrig.com website. This used to work for SS: G90 G21 SET_GCODE_VARIABLE MACRO="RatOS" variable="relative_extrusion" VALUE="True" START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} EXTRUDER_OTHER_LAYER_TEMP={temperature[0]} BED_TEMP=[first_layer_bed_temperature] CHAMBER_TEMP=[chamber_temperature] TOTAL_LAYER_COUNT={total_layer_count} X0={first_layer_print_min[0]} Y0={first_layer_print_min[1]} X1={first_layer_print_max[0]} Y1={first_layer_print_max[1]} As did this for Orca: START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]},{first_layer_temperature[1]} EXTRUDER_OTHER_LAYER_TEMP={nozzle_temperature[0]},{nozzle_temperature[1]} BED_TEMP=[bed_temperature_initial_layer_single] INITIAL_TOOL={initial_tool} TOTAL_LAYER_COUNT={total_layer_count} X0={adaptive_bed_mesh_min[0]} Y0={adaptive_bed_mesh_min[1]} X1={adaptive_bed_mesh_max[0]} Y1={adaptive_bed_mesh_max[1]}

53 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 8/28/2024 in #fix-my-resonance

VC3.1 300 - Chaos on the Y Axis

Aaaah - that is an exciting way to do it 😄 But thank you for all your time and help! Going to close the ticket and just chug through the process or rebuilding.

31 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 8/28/2024 in #fix-my-resonance

VC3.1 300 - Chaos on the Y Axis

That was the stock 2020 & rail.

31 replies

RRCRat Rig Community [Unofficial]

•Created by Heretic_Infidel on 8/28/2024 in #fix-my-resonance

VC3.1 300 - Chaos on the Y Axis

Not super but alot better than what it currently is.

31 replies

Gaming

Programming