Sky217
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
What settings did you end up with? I am running through the same issue
56 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/28/2024 in #fix-my-print
Temp tower question
I think I need to do something with my retraction too.
3 replies
RRCRat Rig Community [Unofficial]
•Created by ADSRMedia on 9/8/2024 in #fix-my-print
Gaps in layers
I have been having all kinds of problems. So far all is fixed at least for now. I got the beacon probe shipped the other day and I am too scared to install it. Trying to enjoy my printer working well for the next few days 😆
18 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I'll check them out
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I just recently changed the hotel as I broke the previous one 😅 and am continuing to use Rapido 2F UHF and the Orbital. As I am bottlenecked by those flow numbers are there better high-flow high temp recommendations setup?
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I was printing at max 23mm^3/s with a .6 nozzle. I came up with that number since I tested my setup a while back with a different brand of PLA and got 30 mm^3/s. Conservatively I chose 23 mm^3/s without testing, but perhaps I chose wrong. I just lowered it to 15 and that fixed the issue. So I am running a max volumetric speed test and will see the result. I also wanted to share this in case someone else runs into the same issue. It was super frustrating since I had spent many hours tuning and returning already.
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Thank you for your comment. I used this spool as a test to learn and tune the crap out of it. I tested and tuned EM, PA, temp like 10 times as I stated in my previous comment. I also dried the spool for 9 hours before use. I will be lowering the volumetric flow rate speed and see if that will make a difference. I suspected that it could be related.
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Could be my slicer settings
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Only happens on curved surfaces
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I just checked! I believe I have it connected correctly.
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Thank you for sharing that input
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
That is very interesting point though
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Interesting! Could you share a picture on how it should be wired whenever and I’ll check. I have done it a while back and can’t remember but I’ll also look
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
It was the extruder step off again. Either it is sensitive to the tension screw or something else. Time will tell.
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
Either the extruder or the motion x/y
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I am starting to assume it could be something with the printer steppers
31 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/6/2024 in #fix-my-print
Random line mystery
I am still working on calibrating and learning as I go the most efficient way to do this. So feel free to ask
10 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 9/12/2024 in #fix-my-print
Help
I'll look tomorrow. I am just too frustrated with it now but thank you for the reply
31 replies