Cristian I
RRCRat Rig Community [Unofficial]
•Created by Cristian I on 2/8/2025 in #ratos-support
Filament unload lenght/speed change for dual filament path extruder setup
Solved by editing the legacy unload filament macro
4 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Awesome stuff Helge! Thank you!
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Here is the macro in question
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Uu, that is nice, did not know that is possible, will give it a try. Thanks!
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
The RatOS implementation for the filter control is nice due to not relying on the slicer to operate, but with this macro, it seems to make slicer control possible, which is kinda a cool discovery for per filament control
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Depending on the filament, how bad they smell. My printer still has some small leaks and if the filament has a strong odor (Bambu Lab ASA for example), it can be felt outside the chamber. In that case, it runs at 50% during the print (set in Orca) and at full blast for 5 minutes after (RatOS). But other filaments that do not exhibit such a strong odor , the filter runs only at the end of the print
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Yeah, so having the filter enabled via the variable at "print_end" + the macro I am using to read the M106 P2 (auxiliary part cooling) and M106 P3 (air filtration) + activating air filtration and setting 0% fan speed for "Complete print" in Orca = the filter fan spun for about a milisecond due to the macro set in RatOS but it was turned off by the slicer, so this combination enables per filament filter control.
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Doing it right now
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
If you want, I can send you the macro, just haven't tested if the filter starts or not when it is set to 0 in Orca and the variable is set to True, now I am curios and will test it tomorrow
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
By setting the variable_chamber_filter_enable: True or False, you can control if it will work or not. You can use the Air filtration settings from Orca slicer, but you need a macro that decodes the M106 P3 commands from the slicer, don't think default RatOS can handle those
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
The current implementation is not filament based
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
43 replies
RRCRat Rig Community [Unofficial]
•Created by tiggo256 on 1/30/2025 in #fix-my-printer
Scan compensation mesh looks wonky
It should and I am pretty sure it does but that big of a range suggests that something mecanical is wrong. Check everything related to Z, especially the leadscrew coupler skrews
6 replies
RRCRat Rig Community [Unofficial]
•Created by tiggo256 on 1/30/2025 in #fix-my-printer
Scan compensation mesh looks wonky
Did you Z tilt before the mesh?
6 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/28/2025 in #ratos-support
Rat Pack wont start
Ok. Think I see the problem now if the config lines above are exactly the ones used your config, the PD15 pin is incorrectly referred to, it should be set to enable_pin: PD15
7 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/28/2025 in #ratos-support
Rat Pack wont start
Did you also activate chamber filter control via the variables?
7 replies
RRCRat Rig Community [Unofficial]
•Created by mufasa81 on 1/23/2025 in #ratos-support
Y-Stepper engages for X-Movement
Use the STEPPER_BUZZ STEPPER=stepper_x (for example) command to identify each stepper as per your printer.cfg, you either have plugged them in the incorrect steppers on the mainboard or selected the wrong motors in the configurator
23 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 1/23/2025 in #ratos-support
Pi Camera on New RatOS
Did you also set it up in Mainsail?
5 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/22/2025 in #fix-my-printer
Access to configurator RatOS
No problem
33 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/22/2025 in #fix-my-printer
Access to configurator RatOS
For 2.1, there is the new documentation available which also has the relevant links https://os.ratrig.com/docs/installation
33 replies