Manuel Sterbizzi
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
unfortunately it gives me random errors sometimes even during the purge line... in the speed test I even reach 1200mm/s then when printing at 900/1000 it crashes
60 replies
RRCRat Rig Community [Unofficial]
•Created by SolomoSalamander on 12/11/2023 in #ratos-support
Octopus Pro 1.1 H723 - flashing will not work
perfect thanks… because I'm considering replacing my manta m8p…. it's giving me a lot of problems that have no solution... and this board is coming to me
74 replies
RRCRat Rig Community [Unofficial]
•Created by SolomoSalamander on 12/11/2023 in #ratos-support
Octopus Pro 1.1 H723 - flashing will not work
does the flash happen even if the jumper is inserted?
74 replies
RRCRat Rig Community [Unofficial]
•Created by SolomoSalamander on 12/11/2023 in #ratos-support
Octopus Pro 1.1 H723 - flashing will not work
sequence: I install ratos, turn on pi and go to configuration… I choose flash via dfu (I already preload the card with the jump)… I compile in firmware…. Then?
74 replies
RRCRat Rig Community [Unofficial]
•Created by SolomoSalamander on 12/11/2023 in #ratos-support
Octopus Pro 1.1 H723 - flashing will not work
Is it necessary to remove the jump with the card turned on?
74 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
👍🏻
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
how many microsteps do you have?
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
and when you exceed the limit, it loses steps, but does not crash the mcu.... so I wonder what problems the manta m8p has
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
I honestly don't think so but it's a problem that I will try to solve after this other problem
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
I reassembled my octopus v1.1…. and I can go in the speed test at 800 and 16000 without problems... with manta m8p max 500... beyond that it crashes
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
then there is this unusual movement of Y while it slides on X... and I don't understand if it is connected to the rest... don't pay attention to the ruined rail, I'm just using them for a test
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
unfortunately even with a new SD, the problem is still here... if I lower the microsteps to 32, I can raise the speed up to 1300mm/s before the error appears... I wonder what is affecting the microsteps...
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
I bought one anyway... I'll try straight away tonight... let's hope it's the correct solution... otherwise I'd like to get an octopus pro
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
But I don't like using the CPU and RAM very high like you... they remain quite low... then I noticed that when I do a speed test, at 500mm/s it ends... at 550 you hear strange noises (it seems like engines), it reminds me like it loses steps (but isn't losing them), and 600 goes into error
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
ok purchased with 32gb... but why didn't it cause problems with the RPI? and with cb1 yes? I am pessimistic and I have doubts that I will resolve with a new SD card.... but it would be fantastic to solve with such a small expense 😂
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
that it arrives soon I only find 128gb... is that too much?
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
on Amazon I find similar to yours but samsung... but 64gb... too big? otherwise I have to wait until Friday to have it like your SD
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
yours is the fastest version... was the one that gave problems like mine?
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
wow…. what version do you have of manta m8p and what version do you have of cb1? maybe then my problem is not the cb1?! I thought it was slow, but if you tell me it's fine... then either mine is faulty, or it's the SD
60 replies
RRCRat Rig Community [Unofficial]
•Created by Manuel Sterbizzi on 12/10/2023 in #fix-my-printer
manta m8p poblem speed
And speed on 16k?
60 replies