anddelbel
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
Got timer too close on t0 while printing with t1…. This was the first time
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
However the fact that t1 doesn’t have any problems leads back to the Ebb42….
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
do you still think i should swap ebb42 or could it be that the raspberry has too little ram?
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
i notice the raspberry has a question mark at the start of its version, not sure if that's normal...
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
same problem occoured again.... probably shouldn't have spoken that soon. It occured while printing a bridge so it should have had any vibrations... I highly doubt at this point it has anytng to do with the actual mobo on the toolhead
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
this seems to have solved the issue
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
i switched the usb to a new one and the problem didn't come back, probably the usb had gotten damaged somehow... I had one of the rat-rig provided ones with the nylon coating.
102 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Faulty VAOC camera (or accessories)
probably its fried, i can't help you any further on this one, you should wait for someone who knows something more may be
14 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Faulty VAOC camera (or accessories)
have you tried to ssh into the pi and make it list the usb connections while its connected?
14 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Faulty VAOC camera (or accessories)
when conected to your pc no signs of life?
14 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Faulty VAOC camera (or accessories)
all is connected as it should, does it heat up when connected?
14 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/2/2025 in #fix-my-printer
Faulty VAOC camera (or accessories)
send some pictures of all the connections you made of the camera, may be you connected it the wrong way
14 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
yeah i meant soldered connections done by me
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
just checked on the printer and the soldered board is t1, so i'll just switch out everything, cable and board. I just have to flash the new one in the configurator right?
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
now that i think about it i should check that with certain movements of that soldered cables the board doesn't get shorted...
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
on the endstop they kept slipping out, I had to push them in to make a contact, couldn't make a proper crimp, so i decided to ask my electrician to solder and insulate...
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
i have a spare board, but i'll have to unsolder the endstop cables... unfortunate, i hope this at least solves my problem
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
102 replies
RRCRat Rig Community [Unofficial]
•Created by anddelbel on 1/21/2025 in #ratos-support
MCU 'Toolboard t0' shutdown: Timer too close.
what should i do next? i'm thinking about replacing cable and then if that doesn't solve the problem the ebb42... do you agree or should i try something different?
102 replies