goofwithz3
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
octopus v 1.1
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
Huh... so which pin number are yoy using? I'm having trouble figuring out which pins on the octopus is a gpio pin?
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
... and the answer is. I had not put the nut on the front of the runout sensor when i built it. D'oh! so, it wasn't working right. put the nut on, tightened everything, and it worked! mechanical problem, not electrical issue. Woot!
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
https://github.com/bigtreetech/smart-filament-detection-module/blob/master/V2.0/Manual/SFS%20V2.0%20User%20Manual_20231123.pdf page 17 specifically says to use PG12 and PG13. im confused here...
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
On the octopus 1.1...
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
Can I get an example pin number?
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/23/2024 in #fix-my-printer
More troubles with a runout detector
@SYG|Krizalid87 Not endstop pins? Which kind of pins then?
18 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/8/2024 in #fix-my-printer
are
And the answer is: My belt tighteners were not seated into the locking nut. they were secured into the PART, but not the nut! My cubes are now square!
12 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/9/2024 in #fix-my-resonance
XY matches, but....not tight enough? maybe?
And the answer is: My belt tighteners were not seated into the locking nut. they were secured into the PART, but not the nut! My cubes are square!
4 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/8/2024 in #fix-my-printer
are
adxl shows they're equal. But i don't know how much tighter they should be.
12 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 1/8/2024 in #fix-my-printer
are
i did the skew print test. the x and y were near perfectly equal. but the skew test looked funny. the edges of the skew test aren't straight. heavily slanted. thats why i did the scaled cube, so i could exaggerate the Z. I did note that the two ABS bits that hold the top of the Z screws weren't well printed -- the prints had some z-banding. so i'm reprinting them. I also am beginning to wonder if my belts might be too loose. I had them both equal, but plucking at about 50 Hz. Something on the internet said 100 herz would be far more appropriate....Plausible?
12 replies
RRCRat Rig Community [Unofficial]
•Created by goofwithz3 on 12/23/2023 in #fix-my-printer
4028 Fan weirdness
yeah, nope. still 7%. I'd really like to figure out what is going with my rpms though...
4 replies