DBWL
RRCRat Rig Community [Unofficial]
•Created by DBWL on 1/22/2025 in #ratos-support
"Must home Axis first" When trying to home after fresh 2.0.2 Install
It was just strange to me since it didn't let me home because it was not homed... thats odd
21 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 1/22/2025 in #ratos-support
"Must home Axis first" When trying to home after fresh 2.0.2 Install
That was my initial thought but didn't want to reflash again as soon as the full release is out.
I will try 2.1 on sunday and mark this as solved if it works.
I need to rerun the skew correction since I upgraded to the 3.1 movement system (bed arms are still 3.0, they will be swapped next week). But everything worked after the mechanical upgrade, I just needed to upgrade to 2.0.2 because upgrading to the latest 1.x version bricked klipperscreen for me.
21 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 1/22/2025 in #ratos-support
"Must home Axis first" When trying to home after fresh 2.0.2 Install
I also tried inserting this from my old printer.cfg but no luck
Safe Z Home (Physical endstops only)
[safe_z_home]
home_xy_position: 150,150 # 300mm printer
#home_xy_position: 200,200 # 400mm printer
#home_xy_position: 250,250 # 500mm printer
21 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
or mark is as solved?
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
Is there a way to close this thread?
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
Yeah might be, first normal Print now and it looks a bit far, but still no gaps. Maybe the test isn't to exact with the first layer or I need higher extrusion multiplier there.
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
Wasn't aware that pa does affect normal extrusion. Thought just for when it stops
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
hope this tool makes it to superslicer/prusaslicer 🙂
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
(still don't know why the first layer has huge gaps even though I put in the same Settings from my printer profile)
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
It is a bit more work to set it up the first time and a lot of sweat running it (with my finger hovering over the emergency stop) but easier to read
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
oh, now I see, thats just one of the two commands you post before starting the print, jeah I did that
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
wait... did I oversee this somehow
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
for now it seems pressure advance is not just a bit off... ellis' test shows somewhere arount 0,02 instead of 0,045 I use now
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
can't find it in super slicer or the printer.cfg
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
Is the square corner velocity set in the slicer?
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
I use 100mm/s for the tower and quite thick layers at 0,45
27 replies
RRCRat Rig Community [Unofficial]
•Created by DBWL on 12/5/2022 in #fix-my-print
Corner and seam problem
I am currently trying this method to determine the pa value: https://ellis3dp.com/Print-Tuning-Guide/articles/pressure_linear_advance/introduction.html
Typical calibration doesn't work for me as it seems
27 replies