Beluga
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
Yes that's from my printer.cfg
How does your config file look? Sharing a pic would be helpful
If I can help I'd be happy to if not im sure someone else can help ya
41 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/12/2023 in #ratos-support
quick question about prime blob(help please)
Thanks tomorrow I'll try and change it
5 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/12/2023 in #ratos-support
quick question about prime blob(help please)
How do I change it the X value in the printer cfg. Prime blob happens on the opposite side of the X endstop
5 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
now I'm off to the fix my print troubleshooting section hahaah
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
Thanks you are THE MAN
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
It worked thank you very much for the help, I deleted all the save_config sections uncommented the z-offset in the bltouch section and re did probe calibration, after that I checked the config file and there was a single save config section with bltouch z-offset commented out
Without errors
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
I see, thanks for the help I'll try it out and let you know👍🏼
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
I'm an idiot that didn't see it after taking a video my bad
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
Oh ok thanks, what about the problem of z-offset in the bltouch section? How do I deal with that?
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
@blacksmithforlife updated this one
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
I uncommented the z-offset in bltouch section to take the video and this is what happens I can't fine tune it, and even if I could I can't use the printer because of the problem I described above
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
Edit*
I can't calibrate the z-offset
If I use the PROBE-CALIBRATE comand then the bed doesn't go beyond a certain point(it goes up and comes back down) when using anything less than the -1 option like -0.1
if i accept it and save it comments out the zoffset under the bltouch sensor and gives me an error saying itsì has to be specified
i recenty tried adjusting it manually
ine the configs(zoffset under bltouch) i cant put negative numbers and if i go lower than 1.300/1.400 the nozzle goes up instead of going down
help i cant adjust it
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
wrong document sorry @blacksmithforlife
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
Sorry @blacksmithforlife
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/2/2023 in #ratos-support
Z offset problem
22 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
extruder rotating in opposite direction
I'm an idiot thanks
3 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
I have a problem
Thanks have a good day
41 replies