nathanjenny
RRCRat Rig Community [Unofficial]
•Created by jay777 on 3/31/2024 in #fix-my-printer
New Beacon setup. No clues...
Mine looks identical. Only thing I'd suggest is being ready to hit emergency stop first try.
7 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/22/2024 in #fix-my-printer
BTT SFS 2.0
I found this in the vcore mods section and it works great!!! BTT V2 SFS Smart Filament Sensor install on Ratrig : https://wiki.circuitlaunch.com/BTT-V2-SFS-Smart-Filament-Sensor-on-Ratrig-6d153a7734e14531a74e5e2cc28e1c38
I couldn't find much help on Discord or the web on installing the Filament Runout Sensor. Here is my Tutorial on it with a V-core 3.1 500 on the Octopus Pro V1.01 board. Hope this helps someone set this up.
6 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/22/2024 in #fix-my-printer
BTT SFS 2.0
But as soon as printer enables the sensor it pauses.
6 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/22/2024 in #fix-my-printer
BTT SFS 2.0
Printer will work if the sensor is disabled in mainsail.
6 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
That was it!!!!!! Wow thanks again!!!!!!!! I really am starting to rack up quite the debt to you!!!!!!!!!
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
Will be a few hours because I kinda want to see if this current print finishes….. it’s a Darth Vader helmet my kids really want….. they’d be bummed.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I’ll try and report back.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I was wondering how it could be so weak.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I am almost 100% certain that’s the problem. I uncommented the first one.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
The first one is half the strength????
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I picked the first one listed but below that one there was some connotation about a different motor.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
Zero bends….. straight shot
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I wonder if I selected the incorrect orbiter in my printer configuration.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
So I was using some with a 2.5mm inside diameter but even that seemed to cause too much drag and so I completely removed it last night.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
What hotend do you use?
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
Ok that seems to be what I’m experiencing. It almost doesn’t have enough strength to pull the filament from the spool which is even on rollers and like 18” from the extruder.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
Mine for sure will start printing after maybe a turn and then for another 1-2 turns max but then I can turn it two to three more times after that and it won’t feed.
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
You mean the one with the spring?
58 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 3/20/2024 in #fix-my-printer
installed bi metal volcano nozzle and my prints will run for anywhere between 1 minute and 2 hours.
I am not sure about said screw either.
58 replies