MichaelKnight
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 3/10/2024 in #ratos-support
changing wifi setting in raspberry pi.
to add, the 2 ssid's were causing the issue. you try to connect to one of them and it wouldn't bind to it.
12 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 3/10/2024 in #ratos-support
changing wifi setting in raspberry pi.
I fixed my issue. turns out for some reason my router was producing 2 ssid's that had the same name at 2.4 no other device could detect these 2 ssid's but somehow the raspberry pi could. i created a guest 2.4 ssid and connected it to that using the ratos.local/configure and it finally connected.
12 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 3/10/2024 in #ratos-support
changing wifi setting in raspberry pi.
good question. i'll pull the sd card out and check the txt out
12 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 3/10/2024 in #ratos-support
changing wifi setting in raspberry pi.
HI, UPDATE, i connect to the configurator, select my ssid, and put in the password. rasp pi reboots, but still displays a ratos hotspot. its not taking to my ssid 😦 is there a manual way of connecting? i've used 2 different devices to connect to the configurator, and i've tried this multiple times already. any suggestions besides reimaging the rasp pi? that would be a HUGE pain.
12 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 3/10/2024 in #ratos-support
changing wifi setting in raspberry pi.
thanks!! will try it out
12 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
agreed. it's time to sleep anyways 🙂 thanks for the help. hopefully the next post is of tensioning success 🙂
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
if i was to do a 3 or 4 colour design, the purges will be minimal i'd assume. no old filament to purge to clean out the nozzle. only a purge to make sure nozzle has filiment in it and ready to go
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
and no wasted filament like the bambo's dirty little secret to those nice looking prints
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
3 or 4 revo hemeras would look awesome. lol
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
yeah, sorry, by multihead, i meant tool changing
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
i think by the time i get to it ( couple years ) more people will have figured it out, and new products will be available
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
you're way ahead of me. i did programming almost 20 years ago in school and then went into an unrelated it field as a career. lol i can't even do hello world anymore
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
i'd love to eventually go with a multihead set up.
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
my mistakes have consequently given me a lot of klipper cfg and troubleshooting experience. but i dont want to build another xy anytime soon. lol
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
i've had an adventure getting this thing set up. the homing is all thrown off, but obviously xy movement needs fixing before i can work on the head getting full bed movement
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
doh
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
its not binding. i'll be downloading the phone app and following another persons instructions posted on here
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
it's not the smoothest x movement. add the cable track i installed that adds some friction, but i'll see the outcome after resonance
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
but x is a bit finicky with movement doing diagnoal in tiny increments. i'll have to do the resonamce test to get tension proper, then see the outcome
106 replies
RRCRat Rig Community [Unofficial]
•Created by MichaelKnight on 1/21/2024 in #fix-my-printer
Z homing issue
now after tightening belts, it's almost fixed.
106 replies