NMGMarques
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
I'll report back if there are any problems.
24 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
Thanks!
24 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
@MDFPereira @miklschmidt seems to be working!
24 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
I'll ping you when I am free again.
24 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
Best on Thursday. I have a team of German coleagues here still tomorrow as well.
24 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 11/27/2024 in #ratos-support
Error after update // dev branch???
If there is anything I can do to help... My knowledge is limited, but I am very willing. :/
24 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
Not so common with 300. 500... Bigger extrusion, more flex... Bigger plate and stuff... All that could allow for my issue on a 300, I wouldn't expect that.
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
Is yours a 500?
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
I guess not. I think we may have bed or frame issues.
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
Bambu Labs 0.6.
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
Sign me up for the exact same issue. I have had it since day one of now going on 2 years. I basically babystep the entire first layer and then also the second and third to adjust gradually. Now, with beacon, it seems to have improved. Although I think it also shows me that there might be something mechanical going on, as after a couple of prints I have to adjust my Z again.
81 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/5/2024 in #fix-my-print
PA-15CF - Printer has been calibrated, yet I keep getting these imperfections.
Added photos for more reference. These are flow tests from 0.75 down to 0.60. As you can see, I am still getting a rough surface and what seems to be stringing.
6 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/5/2024 in #fix-my-print
PA-15CF - Printer has been calibrated, yet I keep getting these imperfections.
6 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
Thanks to all for chipping in!
57 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
I think I have it sorted, now.
57 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
Now the cables from my molex got pulled and are touching-
57 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
The piece that holds my cable guide in place snapped off.
57 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
Yeah... I am having a lot of issues today.
57 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 8/1/2024 in #fix-my-printer
Can't set Z Offset
Without the chamber because I don't have a chamber sensor.
57 replies