eschaos1
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 3/15/2024 in #ratos-support
Bond Tech Extruder binding
The video is an example of trying to load filament and it doesn’t push the material through
5 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
The picture on the guide was shown as the same on both sides so I was misled in the installation. If the left and right side pictures were shown correctly I would have installed it correctly
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
Thanks for pointing this out I was able to determine that it was the idlers that were installed upside down causing the belt not to catch on the left side. ✅
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
The set screws holding the motor drive in place are tight and do not move
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
Or this one on the front side?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
So tighten this set screw?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
They don’t seem like they’re loose (belt is pretty snappy), but you recommend disassembling the x and y motor assemblies to tighten the pulleys more?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
But are those the grub screws?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
Oh ok I’ll put those back
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
And that was for adjusting the belt teeth (default was 40 for a 20 tooth belt for both x and y stepper motors)
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
Are these the grub screws? (One on each side?)
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
@miklschmidt What’s the best way to tighten loose pulleys? Motor wiring seems fine, there are no awful noises. We noticed that adjusting the x stepper to 49 and y stepper to 52 lead to repeatable centering for y but offset centering for x. It still makes a slightly less offset movement for the other axes but still creates an offset drift when moving either axis to the other axis.
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
@miklschmidt Does sensorless homing isolate the axes better? Not sure if it’s a config settings microstep issue, or a belt tension mismatch but tried both of those.
34 replies
RRCRat Rig Community [Unofficial]
•Created by eschaos1 on 11/8/2023 in #ratos-support
Homing causing drifting?
Even when running the command for setting center kinematic position, we see this drifting when adjusting any axis position like moving any amount x automatically moves y (ranging from slightly to a lot)
34 replies
RRCRat Rig Community [Unofficial]
•Created by AllSparkII on 10/3/2023 in #ratos-support
Octopus 1.1 detected but unrespnsive
@miklschmidt Is this network connection requirement for RatOS raspberry pi, Klipper and a octopus pro v1.0 control board needing a WiFi and/or Ethernet hardline? (I’ve tried with my phone as a hotspot but haven’t been successful)
11 replies