FlipBreukers
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Got a Beacon Rev H, was a bit of a struggle to find a decent mount but think I got it covered now. So now it's restart, back to config and go for the beacon right?
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
That's worth a lot, today I calibrated the RR . It is a lot to do.
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Thanks, better to be safe than sorry. It's more expensive but it works. I'll go that way too eventually.
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Great, thx!
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
On the toolboard (EBB 42 1.2)
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
So far the functioning of the BTT microprobe was unsuccessful. I have not received the configs from @MDFPereira yet. I tried a solution from @MDFPereira which was posted on Facebook (ran the configurator, installed a generic probe and included the microprobe.cfg ). No joy, I kept receiving the error "z-probe activated after retraction". Tried inverting the sensor pin setting but error stayed. So I swapped back to an old bl-touch and reconfigured the setup, that works fine. Calibrated and PID tuned bed and extruder. Then I ran the belt tensioning macro. Gave me a nice graph but I'm not sure what to look for. In the low frequencies there is noise on the graph but at the higher frequencies there is less noise shown and both belts are almost equal. How to interpretate or read the graph and translate that to my settings. How are frequencies and speed related to each other and when is a belt too tight or too loose? I hope someone can point me in the right direction.
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Wow, thanks! Most appreciated! Any suggestion on how to calibrate it?
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Any beacon? Or is there a significant difference between brands? I do have a proximity sensor laying around ( Finglai LJ18A3-8-Z/BX-5V) which looks awfully similar to the loose probe/beacon on the RR site. I love tinkering and trying once pointed to the right direction.
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Mikkl, my compliments for your fantastic work. I just switched to klipper (my CR6SE) but the RATOS layer makes it so much easier and better to understand. I'm now in the process of calibrating it . A bit scary for the calibration of the BTT microprobe. Any suggestions?
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
same applied for the EBB 42 1.2 toolboard. That one I could reset (boot+reset release reset and boot) since I had it already wired it was a bit of a challenge to reach the buttons but two ballpens solved that 😉 ) Here it would flash but after the flash the same error. Going back and forth worked fine.
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
At first I chose the DFU method but had not yet placed the boot jumper. I placed the jumper and tried the reset button but nothing happened and the interface kept telling me it couldn't find it. Also hitting the back button and next again with reset press didn't change that. After killing the power and restarting it, I entered the DFU again, it recognised the board and started flashing. After the flash it gave an error. But after going back and next again it walked through
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
I got the (according to the specs on the order from RR) NTC 100K ohm B3950
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
not the one with the microsd card
37 replies
RRCRat Rig Community [Unofficial]
•Created by FlipBreukers on 6/4/2024 in #ratos-support
Which Thermistor to Choose
Nope, reset button didn't do anything after putting the jumper on. I chose the one with the USB connection.
37 replies