Ice
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
Do you want me to post some pics of the test pieces that I printed and the settings that I used?
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
I am running a 0.6 since its a bigger build area and a large print
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
Going to fire up the 44 hour print again this evening after my new bowden tube with the bigger ID comes in.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
@DocDoyle VC3.1 400/500/RatEnder So, I was able to run this test last night. The default profile that I had was running this setting at 200 mm/s for some reason. I ran some tests and brought it down to 21 mm/s. I ran a print much shorter print that I have had this gap issue with and it succeeded with no issues.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
I have a long print running now but I will post the results of the dest once I am able to run it.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
Thank you! I realized there is also an option to calibrate this in OrcaSlicer so I will be doing that as well so that I can get it dialed in.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
This is not from my home profile since I am at work.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
I think that is the similar setting in Orca Slicer
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps

22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
Two things that did change since posting this: I upped the amperage to 0.85A and I added in an Infinity Flow filament feeder which should eliminate some of the friction that was coming from the bowden tube. I have some looser bowden tube on the way as well that I will be replacing the existing tube with.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
Or would it be in the filament settings?
Material Settings > Filament Tab > Flow Ratio and Pressure Advance > Flow Ratio
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 2/23/2025 in #fix-my-print
Extrusion Gaps
I will have to check my settings when I get home. I am running OrcaSlicer, so would this be flow ratio setting?
Quality Tab > Walls and Surfaces Header
22 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Trying to do this giant machine as my test bed and learning for when I set up the next 4 machines.
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Thats what I am using.
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Part of the reason I was asking that is because I am out of slots on the PSU if I do that, so I either have to double up or grab another 24v psu. I can break out one of the power lines since I am using DIN rails.
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Right. I just meant the power that would run from the PSU to the Octopus board: Hot End slot, is no longer needed, correct?
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Oh, dumb question @Helge Keck. Since I am running power for the hot end to the EBB42, do I need to run power for the hot end to the Octopus board?
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
I think that is everything for the time being. Thank you very much for all of your help! I really appreciate it!
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Yeah. Its just a habbit to verify as much as I can.
60 replies
RRCRat Rig Community [Unofficial]
•Created by Ice on 5/26/2023 in #fix-my-printer
EBB42 Where Do I Begin?
Cool.
60 replies