Cruz
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
I need to read this chat carefully 💪😅
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
302 replies
RRCRat Rig Community [Unofficial]
•Created by metal_mp on 3/13/2025 in #fix-my-printer
Squeeky timing pulley
Thanks for the feedback! will add it as soon as I can
12 replies
RRCRat Rig Community [Unofficial]
•Created by QuantumTeddyBear on 1/15/2025 in #ratos-support
IDEX input shaper values not being set correctly
well, @QuantumTeddyBear should have enough info to proceed!
15 replies
RRCRat Rig Community [Unofficial]
•Created by QuantumTeddyBear on 1/15/2025 in #ratos-support
IDEX input shaper values not being set correctly
Make sure to select the IDEX at the begining of the Calibration chapter
15 replies
RRCRat Rig Community [Unofficial]
•Created by QuantumTeddyBear on 1/15/2025 in #ratos-support
IDEX input shaper values not being set correctly
15 replies
RRCRat Rig Community [Unofficial]
•Created by QuantumTeddyBear on 1/15/2025 in #ratos-support
IDEX input shaper values not being set correctly
15 replies
RRCRat Rig Community [Unofficial]
•Created by QuantumTeddyBear on 1/15/2025 in #ratos-support
IDEX input shaper values not being set correctly
15 replies
RRCRat Rig Community [Unofficial]
•Created by Ag_Back on 2/14/2025 in #fix-my-printer
Nozzle scraping bed during beacon calibration
will take care of it
84 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Don't hesitate to message the community 💪
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Oh, yah, you must always restart after running kinematic position
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Try BEACON_RATOS_CALIBRATION
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Run the BEACON_INITIAL_CALIBRATION
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
The middle jumper shouldn't have effect on it
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Could it have been a miss wiring on the pi wires?
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
No worries, it can be confusing
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
Do you have the octopus v1.1 or the octopus V1.1PRO ?
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
It's a bit different from the standard octopus V1.1
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
What I mean is, this is the octopus V1.1 PRO
40 replies
RRCRat Rig Community [Unofficial]
•Created by .sgt.waffles on 11/2/2024 in #fix-my-printer
Octopus 1.1 Firmware Issues + Magic Smoke
The vc4 comes with the octopus V1.1
40 replies