Plynix
Plynix
PostsComments
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Until now not really
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Im currently changing bearings
162 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
but conneted to router
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
ssh also broken
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
ping timeout
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
Now PC, Macbook, Macpc , Phone, diffrent phone
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
Any logs that i can inspect?
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 4/10/2023 in #ratos-support
RatOS dashboard keeps freezing
Issue now persists ssh works fine but dashboard is completely dead
13 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 10/21/2023 in #ratos-support
Orbiter 2.0 Filamentsensor config for Ratrig
ok solved this code works flawless instead of the old one 
[filament_switch_sensor filament_sensor]
event_delay: 0.1
pause_on_runout: True
runout_gcode: 
    UNLOAD_FILAMENT
insert_gcode: 
    LOAD_FILAMENT
switch_pin: ^!toolboard:PB4 

[gcode_button sensor_button]
pin: ^PC7
press_gcode: 
  UNLOAD_FILAMENT
[filament_switch_sensor filament_sensor]
event_delay: 0.1
pause_on_runout: True
runout_gcode: 
    UNLOAD_FILAMENT
insert_gcode: 
    LOAD_FILAMENT
switch_pin: ^!toolboard:PB4 

[gcode_button sensor_button]
pin: ^PC7
press_gcode: 
  UNLOAD_FILAMENT
thanks to Helge Keck
14 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 8/3/2023 in #ratos-support
Orbiter on Ocotopus v1.1
No description
6 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 8/3/2023 in #ratos-support
Orbiter on Ocotopus v1.1
How the hell does it work
6 replies
RRCRat Rig Community [Unofficial]
Created by Plynix on 8/3/2023 in #ratos-support
Orbiter on Ocotopus v1.1
i remaped the pinda probe to an endstop port now bltouch is free
6 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
When I change the belt it pressed against then with a screw inside and they where freely to rotate
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Se the line on the belt maybe I will change the bearing
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
No description
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Yeah I will change it but it can’t make those sinusoidal motions
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Maybe this is making the issue it’s like moving up and down
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
The belt might nut nur perfectly in the middle maybe hits a side of the motor mount
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Ugh i might rebuild it but now square
162 replies
RRCRat Rig Community [Unofficial]
Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Ok how did it behave any fix?
162 replies