Christian - cbTechnology
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
It correlates with the perimeter crossing so i think it has something to do with nozzle oozing. But it makes no sense because i already print at 200°C which is low for BBL PLA (220°C at the X1C)
11 replies
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
It should be matte because it is matte filament 😄
11 replies
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
I also tried different retract speeds and it made no difference
11 replies
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
11 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
:chefkiss:
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Passt
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Falls es dringend ist
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Und wenn du es ned hin bekommst, kann ich dir die Dinger auch gerne zum material Preis + Versand drucken 😊
Schwarzes ASA habe ich da
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Welche speeds fährst du?
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Das einfachste wäre es mal mit nem Klebestift zu probieren. Drucke regelmäßig 25x25cm große ASA Bauteile und dat läuft
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Also ich habe einfach Klebestift genommen, den ordentlich aufgetragen und mitm Spatel verstrichen. Bei mir haftet ASA perfekt.
16 replies
RRCRat Rig Community [Unofficial]
•Created by Rigattoni on 5/18/2023 in #german-support
ASA und die Haftung...
Magoo ist ein Haftmittel oder?
16 replies
RRCRat Rig Community [Unofficial]
•Created by correct-apricot on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
🥳
84 replies
RRCRat Rig Community [Unofficial]
•Created by yelping-magenta on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Bin da selbst etwas ratlos. Vllt weiß @Helge Keck was
84 replies
RRCRat Rig Community [Unofficial]
•Created by metropolitan-bronze on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Hmm
84 replies
RRCRat Rig Community [Unofficial]
•Created by correct-apricot on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Den pin wo dein GND liegt
84 replies
RRCRat Rig Community [Unofficial]
•Created by optimistic-gold on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Den PA8 muss man gar nicht angeben
84 replies
RRCRat Rig Community [Unofficial]
•Created by solid-orange on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Weil ich habe das Pro
84 replies
RRCRat Rig Community [Unofficial]
•Created by exotic-emerald on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Hast du den pin nachgeschaut ob der auch bei dem genau so heißt
84 replies
RRCRat Rig Community [Unofficial]
•Created by conscious-sapphire on 5/18/2023 in #german-support
Octopus 1.1 - Part Cooling 4028 - nur vollgas
Welches Board hast du denn
84 replies