Fierux_GAGATAM
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I will dissasemble motors plates, will update tomorrow!
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
ok replacing stepper driver didnt helped
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Yes, then I will be doing this, it is quite a work to dissasemble motor plates assemblies..
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I am trying to switch stepper drivers now again
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Right motor is not working in Standard configuration, but in Hybrid it does work...
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I think keeping it colder it helps.
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Combo of ti tube plus foil might drop the heat soak time
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
minutes*
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Thats good one I will try it in 40 mins
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Do you mean to set config to not hybrid?
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I believe so and we print plenty of ABS/ASA 20-30 heatsl soak needed but no issues on first layer.
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
Ah sorry, I have hybrid config, but belts are not installed yet for hybrid.
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I measured resistance on all stepers, between windings at 1.1 ohm equal, do you think that still can be faulty?
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
I am on hybrid
39 replies
RRCRat Rig Community [Unofficial]
•Created by Fierux_GAGATAM on 2/21/2025 in #fix-my-printer
Y axis stutters during movement
39 replies
RRCRat Rig Community [Unofficial]
•Created by Alexander Wiltschek on 12/31/2024 in #ratos-support
Internal error during connect: module 'extras.resonance_tester' has no attribute 'SweepingVibrations
Yes, ive accidently send it to wrong section. Alredy fixed!
33 replies
RRCRat Rig Community [Unofficial]
•Created by Alexander Wiltschek on 12/31/2024 in #ratos-support
Internal error during connect: module 'extras.resonance_tester' has no attribute 'SweepingVibrations
After update of everything, my camera is not showing anymore in mainsail, and shows Connecting to http://xxxxxxxxxxxxx/webcam/?action=stream, but if I paste this link in to the new tab then I can see the stream from camera, any idea how to fix this?
33 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
1877 replies