andersbr
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
most exiting filament change after emptying a whole expensive roll on a part. Be carefull with the splicer method on such brittle filament, the splice might snap in bowden before it even reaches the hotend. Perhaps better is to stay close and monitor the filament transition, then you could just push the next filament behind the other until it is grabbed by the extrudergears.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Amazing to print this big in ABS wihout warp. When you slice the big bottom plate with some sort of CF filament, doses the slicer calcualte less than 1kg will be used? when i sliced for PET-CF, 25% gyroid and 4 walls it came out scary close to 1kg. dont remember bu tit was like 996g or something. What are the strength settings you use or recommend?
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Nice:chefkiss: i also am going to print the Chonk parts as well soon. But the big parts are scary. What material u used? Did it end up without warp?
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
no, didnt think of that.. this was just to check if the temperature reported was correct.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
nevermind, is saw you confirme that the other day😋
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
the gcodes i looked at was for 0.4
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
You are using 0.4mm nozzle, right?
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
bcause two top layers is in reality just a bridging flow layer + a single top layer
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
i looked at the file, it was just two top layers. I would be cool to see another attempt but with minimum 5 top layers.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
there is a very consistent geometric pattern on these prints. could it also be the top fill that is sagging a bit the infill (gyroid?) due to high temp or too little cooling on the top layers ?
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
m6 threads
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
6mm
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
maybee i should try to stick a termocouple down into the meltzone of my own rapido later today to see what is the temperature with my setup.. i just last week "upgraded" from rapido 1 HF plus to a rapido 2 UHF plus and have had only issuess. until i increased my temperatures a lot.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
don' t trust the temperature in mainsail. I'm even struggling printing PLA under 230 degrees with rapido 2 plus using the uhf adapter and tungsten nozzle. and that is with 20mm3 flow limited.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
you can also go down to 10 flow cap in filament setting. just to remove as many variables as possible. and for simple testprints temperature can also be increased just to lower the viscosity / extrusion force. (it is difficult to know what the nozzle temperature really is as it is very depending on the heat transfer and proper assembled hotend)
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Have you tried printing a cylinder in vase mode using same mm3/s flow. it does not show any extrusion problems there? Have you confirmed the extruder/hotend is not the issue by running a max flow test in orca using the same temperature?
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
with idex it is harder to setup and tune, because you need to use the 2 y motors from the start i think.
1455 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
If everything fails you have the option to go back to basics, (remove a toolhead to rebuild to corexy non-idex) with or without Y(hybrid) motors. But that is a serious job just to troubleshoot..
1455 replies