Yelti
RRCRat Rig Community [Unofficial]
•Created by Jurovan on 1/14/2024 in #fix-my-printer
I am done
It's a good start and it will explain you the basics
8 replies
RRCRat Rig Community [Unofficial]
•Created by Jurovan on 1/14/2024 in #fix-my-printer
I am done
That's the extruder calibration. Try to follow: https://teachingtechyt.github.io/calibration.html
8 replies
RRCRat Rig Community [Unofficial]
•Created by Jurovan on 1/14/2024 in #fix-my-printer
I am done
Did you do any flow calibration? I would check that out.
8 replies
RRCRat Rig Community [Unofficial]
•Created by wise-white on 1/2/2024 in #fix-my-mesh
V-Core 3.1 400m bed mesh twisted near back of printer
It's quite normal for a fresh build. You can follow https://www.youtube.com/watch?v=h7ZTq2dDTkM&t=1236s, that should help you get started.
2 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
Good luck😀
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
You also need to use the pt100 port, not the th0
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
Docs from btt say it's a pt100
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
It seems you confuse a nt100 with a pt100
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
Ok, then check your jumper settings on the ebb
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
The max31865 chips is not a temperature setting.
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
So the thermistor is a pt100, so a special type, you need an extra max31865 chip on your ebb42.
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
Typo😋
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
That's your issue
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
You still don't have the max config ant the pt100 settings
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
Also check your jumper settings see, https://www.dropbox.com/s/ffl4m7txx41ptyu/BigTreeTech%20EBB42%20connections%20information.pdf?dl=0
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
sensor_pin: EBBCan: PA4
spi_bus: spi1a
rtd_nominal_r: 100
rtd_reference_r: 430
rtd_num_of_wires: 2
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
You need something like this:
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
It seems to be a pt100 thermistor, then you need a max31865 chip on the ebb42. Maybe you can disassemble it and change the thermistor to your previous one
47 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 12/9/2023 in #fix-my-printer
Extruder Temp Of the charts
For the th0 of the ebb you need to use: toolboard:e_sensor_pin, otherwise it will expect to be on the octopus board th0
47 replies