ant
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 4/25/2024 in #fix-my-print
Extruder clicking and massive under extrusion
you need a bunch of things in balance
5 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 4/25/2024 in #fix-my-print
Extruder clicking and massive under extrusion
clicking can be when it's not able to melt and push the filament through at the rate that it'sp rogrammed to feed at or it can be that the feeder mechanism is damaged.
based on your testing.. i think raising the temp to stop the clicking means that that has improved your flow but then you have other problems. how about trying to print slower so it doesn't feed as fast?
based on your testing.. i think raising the temp to stop the clicking means that that has improved your flow but then you have other problems. how about trying to print slower so it doesn't feed as fast?
5 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
Make a new thread
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
Oh no
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
My bed velocity is 30m/s 1k accel I think
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
Extrusion temp and cooling is the next challenge for me to figure out
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
I just know that there’s no skipping or anything at these settings
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
But i haven’t tuned it well yet
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
Printing is like 500m/s perimeters and infill I think
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
I use 1000m/s travel 20k accel
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
When I switched to 5160T 50v x/y drivers
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
There’s a speed page with settings you can adjust
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
I’m using prusaslicer
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
Nice!
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
if you can't get that to work, anything else working is by chance
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
i would focus on getting the first layer test to work
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
you never got the first layer test to work perfectly?
242 replies
RRCRat Rig Community [Unofficial]
•Created by E-TF[102] Riker on 10/25/2023 in #fix-my-print
Second Hand 3.1 with 0.8mm Nozzle not printing
well the fact that your recent print popped off your print bed means still some sort of layer adhesion issue
242 replies