Gizzle
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Tbh, the pattern etc are ass. I am mostly set a value by printing some real parts with the speeds I'm using.
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Well I tuned my vcore quite good at 220mms outer perimeter speed :kekw:
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
I found a way to reduce the artifacts for me. The solution was more speed. Normal print speeds are too slow for the vcore
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
How loose and how did you measure it?
162 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 1/23/2024 in #german-support
ROME Extruder 2 IFCNT Fehler
Hab Motor Power angeschlossen und bin dann auf die Motor ports 4 und 5
6 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 1/23/2024 in #german-support
ROME Extruder 2 IFCNT Fehler
Nach bissl hin und her gehts nun...
6 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 1/23/2024 in #german-support
ROME Extruder 2 IFCNT Fehler
Anbei noch das Log
6 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Rail and Idler bearings for fushi bearings
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Had the same issue and it may seem I have fixed it: throw the shitty bearings and belts out. Ratrig uses so bad quality parts in this case
162 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 10/12/2023 in #german-support
Ringing trotz Input Shaper
Der ADXL ist Bomben fest. Ich zieh die ganzen toolhead Schrauben Mal nach. Die y Achse hab ich auch geprüft, werde aber nochmal eine rail lose machen und die dann zueinander ausrichten. So flüssig lief die y Achse nie wirklich.
Riemen können durchaus zu fest sein, ich hab die auf Ner länge von 15cm zwischen Front idler und joiner auf 130Hz gespannt
7 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 10/12/2023 in #german-support
Ringing trotz Input Shaper
Ich kann das nicht wirklich deuten, was ich ändern muss
7 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 10/12/2023 in #german-support
Ringing trotz Input Shaper
7 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 10/12/2023 in #german-support
Ringing trotz Input Shaper
Gedruckt wurden internal perimeter mit 150mm/s und external mit 100
7 replies
RRCRat Rig Community [Unofficial]
•Created by Luciano on 9/16/2023 in #german-support
Problem mit Dual 5015 part cooling und multi anschluss
Helge meint, du sollst under das Include vom Toolboard das mit dem multi_pin setzen
53 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
Are there any reference values regarding the frequency or so?
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
I thought that too, that's why I tried to listen at the motor mounts during movements. In my case there was no noise which could indicate that the belt is rubbing
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
I don't think the frame has anything to do with the issue
162 replies
RRCRat Rig Community [Unofficial]
•Created by Maba_Kalox on 6/7/2023 in #fix-my-print
belt ripples artifact
162 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 5/15/2023 in #ratos-support
Unable to overwrite Octopus ADXL config
tbf, that one did not work either 😄
11 replies
RRCRat Rig Community [Unofficial]
•Created by Gizzle on 5/15/2023 in #ratos-support
Unable to overwrite Octopus ADXL config
I'm not using the toolboard config from ratos, it's my own since I'm using CAN
11 replies