CeredD#77
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
Ok Thank you, im gonna check it at the Weekend in my free time
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
Yes here
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
Measure the heating bed again?
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
What other options do I have?
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
It doesn't matter which cable from the heating bed is connected to HB + or -, does it?
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
Yes
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
I'm getting desperate with the printer...
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
I removed the fuse and measured the resistance at 0.0 and also checked the continuity and heard the beeping.
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
The left one is Slightly browner on the outside like the right fuse
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
I removed the defective piece and connected both ends with a wago.
Was able to print for 32 hours.
But now I get the same message. And the LED for the heating bed is not lit.
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
Can I cut out the defective piece and re-solder it?
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
The new Bed to? I mean i printed 100h before without any problems...
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
The Bed is not heating anymore
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #fix-my-printer
Heater_Bed Not Heating at expected rate
I dont have a SSR ist a V Minion with the Skrat Board
29 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Schade , trotzdem danke
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Ist ein V minion, also der hat kein SSR.
Hatte ich vergessen zu erwähnen, sorry.
Und es ist ein Skrat Board verbaut
13 replies