Bizilux
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
I disconnected the 4 duponts and connected power supply to rpi.
Now i got the error TMCuart_response timeout... I guess those 4 dupont wires need to stay connected?
I thought USB is enough between octopus pro and rpi
I'll try with those 4 wires in as well
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
got a clean klippy log of just the error... i tried a new gcode if that was the problem, but its not... like 4517 has nul all over it
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
its a whole line of NUL... but why that happened?
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
i think on the new log i found where it crashed.
now why it crashed is a different story...
lines 19160
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
part cooling fan started blazing, like when on startup of the printer it starts blazing until klipper starts up... so i think something resets the printer :S
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/7/2024 in #fix-my-printer
First longer print attempted, printer stops after 1 hour
13 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
splendid. it works. I used this command in the end.
[fan]
pin: !fan_part_cooling_pin
cycle_time: 0.01
lets finally try to print something. thanks for your help!
16 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
yes i thought it was set to 24v on the picture, i didnt see
16 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
oh okay its on 12v on picture too
16 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
ok i will. minus the green jumper. the 4028 fan that was shipped to me is 12V
16 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
mine is wired exactly like this for now: https://os.ratrig.com/docs/boards/btt/octopus-pro-446/
16 replies
RRCRat Rig Community [Unofficial]
•Created by Bizilux on 4/5/2024 in #fix-my-printer
How to control part cooling fan on octopus PRO?
i did not, because i dont know what board is in the picture.
I already almost friend motherboard and raspberry pi because uart pins are different between pro 1.0 and v1.1 octopus
16 replies