spoown
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
@Helge Keck well it worked only with band aid 😅 had T0 VAOC camera almost 0.2mm to the right side on the nozzle, and VAOC centered on T1 results:
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
I'll try a fresh new one with more tension then this band aid. Thanks for inputs
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
50% to guess the right side
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
where? the variables are reseting after VAOC calibration
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
np Helge... It's a consistent gap, I would like to compensate it manually...
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
I'm trying now printing with half turn more tension on X belts...
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
SET_SKEW XY=141.75,141.71,100.05
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
I did...
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
do we have a variable to correct that gap manually ?
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
I can turn half more tension on both X1 X2 belts
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
well, it's touching both metal plates perfectly
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
for the gantry I can put the Y at endstop and check spacing from the front exstrusion on left and right side right?
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
I did before the prints..
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
that's the last I done, it ended at 70Hz by demand
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
this time the pic is better quality
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
Same results, you can see on the skirts too
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
63 replies
RRCRat Rig Community [Unofficial]
•Created by spoown on 11/9/2024 in #ratos-support
IDEX and T0 T1 not matching print coordinates (x shift)
SET_SKEW XY=141.75,141.71,100.05 loaded, heatsoaked bed and now printing again squares test after a fresh homing and VAOC calibration
63 replies