flow4enol
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
I doubt it, this is what I get with unklicky
probe accuracy results: maximum 15.510000, minimum 15.500000, range 0.010000, average 15.506620, median 15.507500, standard deviation 0.00160546 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
ensuring klipper is updated is a good idea too, but I don't remember seeing commits related to meshing
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
it's a pain having to deal with it manually
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
hehe, I never tried but I think you might even be able to probe more if you wish, though I don't see advantages
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
something you could try is probe the 4 corners instead of 3 points, at least for me gives me a more even mesh. tilt range will increase though, but I don't see that as a downside, I'm willing to take a worse tilt range and a better mesh
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
I would give the frame just a little more, I still see 2 opposite corners higher than other 2.
another question how many probe points do you have for z tilt?
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
those .12 on mine is 250 and I have seen better on the same size, I believe you may be able to get better, hard to but possible
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
300mm?
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
trial and error works 😅 that's how I found out the right way.
Maybe try to raise Y extrusions (the ones where the rails are) something like 1mm. check what happens carefully don't even print
home, z tilt, mesh
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
mine was squishing on the right I believe (not 100% sure) and too high on the left
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
yes, just a little
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
you don't have much to lose IMO
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
I still think it needs a little adjustment
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
depending on frame stiffness, which as I already said IDK how RR frames behave my experience is with a 2020 frame, the idea is to "skew" the frame a little to see if it improves mesh, the final fix would be adjusting Y extrusion, you can go directly to that step if you wish to experiment
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
most likely irrelevant, how does a repeatability test look on the euclid
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
there's a slight something on the corners that reminds me my issue, you could try to shim the front right foot of the printer, if the frame gives just a little you might see differences, I'm not sure how rigid VC frames are
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
if there's something I learned is that triple z exposes a lot in some "unsquareness" cases even small ones
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
what probe are you using
46 replies
RRCRat Rig Community [Unofficial]
•Created by mysticfugazi on 4/19/2024 in #fix-my-mesh
Mesh not compensating in back of print volume VCORE3 300
nope not much but there was a clear taco shape between 2 opposite corners of the bed
46 replies